-
8-Channel Digital Capacitive Switch Touch Sensor Module For Arduino – TTP226
₦ 1,500A capacitive touch module which sends out signals on contact, it can be interfaced to an Arduino or any microcontroller. This module can be used to build all kinds of interesting projects from access control, home automation, automotive projects etc
- Onboard TTP226 capacitive 8 keys touch sensor IC
- Onboard 8 channel level status indicator
- Working voltage: 2.4V-5.5V
Qucik View -
ADXL335 3-Axis Analog Output Accelerometer Sensor
₦ 7,500The ADXL335 3-Axis Analog Accelerometer is excellent for your drone and motion sensing projects. With a very simple 3-axis analog output, it has a minimal I/O requirement.
- 3-axis sensing
- Small, low-profile package
- Low power – 350 μA (typical)
- Single-supply operation
- 1.8 V to 3.6 V
Can withstand up to 10,000 g shock
Qucik View -
Body Scale/Load Sensor 50kg
₦ 2,000This load sensor, sometimes called a strain gauge, is the same one found in digital bathroom scales (you know, the ones you use in January for your New Year’s resolutions, and then forget about a month later). This sensor can measure up to about 110 pounds.
Qucik View -
Bosch BMP180 Barometer Pressure/Temperature/Altitude Sensor (Arduino Compatible)
₦ 1,500The BMP180 is a precision barometric pressure, temperature and altitude sensor from manufactured by Bosch. It is fully compatible with BMP085 in terms of firmware/software/interfacing. BMP180 can easily be configured to work with Arduino, ARM or PIC over I2C.
Specification
- 3-5V Logic and Power
- Pressure sensing range: 300-1100 hPa (9000m to -500m above sea level)
- Up to 0.03hPa / 0.25m resolution
- -40 to +85°C operational range, +-2°C temperature accuracy
- This board/chip uses I2C 7-bit address 0x77.
Arduino sample code: //www.haoyuelectronics.com/Attachment/GY-68/bmp085_arduino.zip
Datasheet: //cdn-shop.adafruit.com/datasheets/BST-BMP180-DS000-09.pdf
Product InformationBrandQucik View -
DHT-11 TEMPERATURE SENSOR
₦ 2,000The DHT11 is a low-cost and reliable digital temperature and humidity sensor. Digital output only. It is compatible with Arduino complete with library as well as other microcontrollers.
- 3 to 5V Operating range
- 2.5mA (max)
- 20-80% humidity readings (up to 5% accuracy)
- 0-50°C temperature readings (up to ±2°C accuracy)
- 1 Hz Maximum sampling rate
- 15.5mm x 12mm x 5.5mm
- 4 pins with 0.1″ spacing
Pins
1. VCC
2. Data
3. NC
4. Ground
Qucik View -
DHT22 Temperature and Humidity Sensor
₦ 4,000DHT-22 is a humidity and temperature sensor with read out over single wire digital interface. The sensor is already calibrated and doesn’t need extra components so you can measure relative humidity and temperature right away.
- 3 to 5V power and I/O
- 2.5mA max current use during conversion (while requesting data)
- Good for 0-100% humidity readings with 2-5% accuracy
- Good for -40 to 80°C temperature readings ±0.5°C accuracy
- No more than 0.5 Hz sampling rate (once every 2 seconds)
Qucik View -
Digital Capacitive Touch Sensor – TTP223B
₦ 2,000This device allows you to add touch functionality to your designs. It can be easily interfaced with an Arduino or other microcontroller GPIO pins.
Features:
- Operating Voltage: 2-5V
- Chip: TTP223B
- Response Time: 60-220ms
- PCB Size: 28x20mm
- Fully Arduino Compatible
Qucik View -
DS18B20 Waterproof Temperature Sensor – Arduino Compatible
₦ 2,000The DS18B20 allows you take temperature readings in water or oils within its specified temperature range.
DS18B20 Technical specs:
- Usable temperature range: -55 to 125°C (-67°F to +257°F)
- 9 to 12 bit selectable resolution
- Uses 1-Wire interface- requires only one digital pin for communication
- Unique 64 bit ID burned into chip
- Multiple sensors can share one pin
- ±0.5°C Accuracy from -10°C to +85°C
- Temperature-limit alarm system
- Query time is less than 750ms
- Usable with 3.0V to 5.5V power/data
Work with Arduino IDE on ESP8266 Wifi module to take temperature readings over the Internet: //iot-playground.com/blog/2-uncategorised/41-esp8266-ds18b20-temperature-sensor-arduino-ide
Qucik View -
F249 Infrared Motor Speed Sensor Module
₦ 1,500Qucik View -
HB100 Motion Detection Microwave Sensor Module
₦ 3,500This is a X-Band Bi-Static Doppler transceiver module. This module can be used to detect motion in projects relating to home automation, automatic doors, alarm systems and even vehicle speed detection.
Feature
Transmission frequency: 10.525 GHz
Frequency Setting Accuracy: 3MHz
Output power (minimum): 13dBm EIRP
Operating voltage: 5V 0.25V
Operating Current (CW): 60mA max., 37mA typical
harmonic emission: <-10dBm
Pulse mode:
Averagecurrent (5% DC): 2mA
Pulse Width (Min.): 5uSec
load cycles (Min.): 1%Qucik View -
HC-SR505 Mini PIR Motion Sensor
₦ 1,500HC-SR505 is a mini PIR motion sensor for detecting human presence and motion. It is highly sensitive and has low power consumption. It’s 3 pin interface makes it easy to interface with any microcontroller/Arduino or other electronic control circuitry.
Qucik View -
HX711 Load Cell Amplifier Module
₦ 1,500This module uses 24 high precision A/D converter chip hx711. It is a specially designed for the high precision electronic scale, with two analog input channel, the internal integration of 128 times and programmable gain amplifier. The input circuit can be configured to provide a bridge type pressure (such as pressure weighing sensor mode). It is of high precision, low cost and ideal sampling front-end module. Weight:5 g Size:40mmx20mm/1.56″x0.79″(inch) (approx)
Qucik View
