-
10MM RGB LED Module
₦ 2,500Product Description:
10mm LED module featuring red, green or blue output. Suitable for use with microcontrollers including Raspberry Pi or Arduino, the module is ideal for indication and illumination projects.
Features:
- 10mm RGB LED
- Requires current limiting resistor to prevent the LED from burning out
- Forward current: 20mA
- Forward voltage: 3V
Qucik View -
12V LED Power Indicator Module
₦ 1,500Description:
This is Four Battery Indicator LED Light XD-82B 12V Battery Level Indicator Module. This module has on-board precision voltage detection chip and power regulator chip. And on-board four battery indicator LED lights, three colours display, red, yellow, yellow, green representing 20%, 50%, 80% and 100% of the electricity. You can set aside all the way battery testing interface, and two mounting holes located. This module is ideally suited to monitoring the status of a 12V battery.
Through clever use of a series of resistors and the LM339 comparator, a visual indication of the state of a battery can been seen. As the battery depletes and the voltage begins to fade lights will begin to go off>
- Built-in precision voltage detection chip and power regulator chip.
- On board four LED battery indicators.
- Set aside all the way to the battery test interface, and two mounting holes are located.
Qucik View -
24 Bit WS2812 5050 RGB LED Lamp Panel Module
₦ 4,000Description:
The 24 Bit WS2812 5050 RGB LED Built-in Full-Color Driving Lights Circular Development Board has a round black shape, let us be clear at a glance! 24 super bright smart NeoPixels LED arranged in a 86mm outside diameter circular PCB.
These ring RGB lamps can be simply connected via the output pin cascade one to the other’s input pin (DI-DO). In this way, by using only one single chip you will be able to control as many LED lights as possible, each LED lamp is integrated with a driver chip in it so that our LED becomes intelligent and addressable.
Each has a -18mA constant current drive, so the LED color will be very uniform, even if the voltage change is the same, do not need an external resistor current limiting resistor to make the overall design of the RGB lamp ring to become slim, as you see so simple and easy to use. With a 5V power supply to drive the RGB lamp ring.
Characteristics:
Single wire communication, to maximize the reduction of I/O port pressure, and the use of the RGB WS2812B driver chip, so that the peripheral circuit requires only a single capacitor can meet the needs of the circuit, give people the enjoyment of beauty, in addition, this RGB ring, but also through a simple Dout input port, and the other using the same chip RGB lamp cascade, without need considering the shape of the limit.
Features:
- The control circuit and the LED share the only power source.
- Control circuit and RGB chip are integrated into a package of 5050 components, forming a complete control of pixel point.
- Built-in signal reshaping circuit, after wave reshaping to the next driver, ensure wave-form distortion does not accumulate.
- Built-in electric reset circuit and power lost reset circuit.
- Each pixel of the three primary colors can achieve 256 brightness levels, or 16M colors full-color display, and scan frequency not less than 400Hz/s.
- Cascading port transmission signal by a single line.
- Any two points the distance more than 5m transmission signal without any increase circuit.
- When the refresh rate is 30fps, the cascade number is not less than 1024 points.
- Send data at speeds of 800Kbps.
- The color of the light was highly consistent
- Full-color module, Full-color soft lights a lamp strip.
- LED decorative lighting, Indoor/outdoor LED video irregular screen.
Qucik View -
5 Red LEDs + 5 Resistors
₦ 6005 Red LED with 5 330 Ohm resistors. With these, all that needs to be done is connect to Microcontroller or Arduino GPIO pins. Works fine for 5V or 3V circuits
Qucik View -
5 Yellow LEDs + 5 Resistors
₦ 6005 Yellow LED with 5 330 Ohm resistors. With these, all that needs to be done is connect to Microcontroller or Arduino GPIO pins. Works fine for 5V or 3V circuits
Qucik View -
5A DC-DC CC/CV Lithium Charger LED Driver Power Module
₦ 2,500This very utilitarian board delivers constant voltage or constant current output and comes in handy as a battery charger (Lead acid or Lithium battery), LED Constant current driver, as well as other power supply needs. It is also quite chunky -deliverying up to 5A output.
-
- Output voltage: 0.8V-30V
- Input voltage: 5V-32V
- Separately adjustable voltage and current outputs
- Size: 51 * 26.3 * 14 (L * W * H) (mm)
- Operating Temperature: -40 to +85 Degrees
- Voltage Regulation: +/-2.5%
- Load Regulation: +/- 0.5%
- Output ripple: 50mV
- Switching frequency: 300KHz
- Conversion efficiency: 95% (the highest)
- Output current: adjustable maximum 5A
Qucik View -
-
USB LED Light – 24pcs
₦ 4,000Description:
Power Source: DC
Is Batteries Included: No
Brand Name: HEGUOGUO
Light Source: LED Bulbs
Is Batteries Required: No
Certification: ce
Is Smart Device: no
Origin: CN(Origin)
Features: Mini
Item Type: Book Lights
Model Number: 5V USB Book Reading Night light
Wattage: 1W
Qucik View -
USB LED Light – 8pcs
₦ 2,000Description:
Power Source: DC
Is Batteries Included: No
Brand Name: HEGUOGUO
Light Source: LED Bulbs
Is Batteries Required: No
Certification: ce
Is Smart Device: no
Origin: CN(Origin)
Features: Mini
Item Type: Book Lights
Model Number: 5V USB Book Reading Night light
Wattage: 1W
Qucik View