Only logged in customers who have purchased this product may leave a review.
Digital Capacitive Touch Sensor – TTP223B
₦ 1,200
This device allows you to add touch functionality to your designs. It can be easily interfaced with an Arduino or other microcontroller GPIO pins.
Features:
- Operating Voltage: 2-5V
- Chip: TTP223B
- Response Time: 60-220ms
- PCB Size: 28x20mm
- Fully Arduino Compatible
3 in stock
Related Products
-
MQ-2 Combustible Gas Sensor – Arduino Compatible
₦ 3,000This sensor allows you to detect combustible gases in the air. It is capable of detecting flamable gases in concentrations ranging from 300 to 10,000 ppm using only one analog pin from a microcontroller.
5V Operation
Detects any of the following flammable gases- LPG
- Butane
- Propane
- Methane
- Alcohol
- Hydrogen
- Smoke
Example Application: Fire prevention system, Gas leakage detector, Gas concentration detector.
Qucik View -
MQ-8 Hydrogen Gas Sensor – Arduino Compatible
₦ 3,000The MQ-8 hydrogen gas sensor, allows hydrogen gas concentrations to be measured. It has a sensitivity of 100-10000ppm. The Output is simply connected to an ADC via a load resistor
- 5V Operation
- Easy connection
- Highly sensitive
Qucik View -
LM35 Temperature Sensor
₦ 980The LM35 is a precision integrated-circuit temperature sensor with an output voltage linearly-proportional to the Centigrade temperature. The very popular LM35 temperature sensor is displays 0.1V to 1°C and can be interfaced to any Arduino or microcontroller ADC with no external components
Features
- Calibrated Directly in Celsius (Centigrade)
- Linear + 10-mV/°C Scale Factor
- 0.5°C Ensured Accuracy (at 25°C)
- Rated for Full −55°C to 150°C Range
- Suitable for Remote Applications
- Low-Cost
- Operates from 4 V to 30 V
- Less than 60-µA Current Drain
Can be used to measure temperature in different kinds of electronic projects
Qucik View -
Photosensitive Resistance Sensor Module
₦ 1,800This photosensitive resistive sensor module is handy in home automation and solar applications. The sensitivity can be varied using the potentiometer. Additionally, it is capable of driving up to 15mA.
Features
- Operating voltage of 3.3 V to 5 V
- DO digital switch output (0 and 1) and AO analog voltage output
- Adjustable senstivity
+ power supply positive
– connect power cathode
DO TTL switch signal output
AO analog signal outputQucik View -
Infra-Red Flame Sensor
₦ 600This module is sensitive to the flame and radiation. It also can detect ordinary light source in the range of of a wavelength 760nm-1100 nm. It can be used as a flame alarm or in fire fighting robots.
Features
Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm.
Detection range: up to 100 cm.
Adjustable detection range.
Detection angle about 60 degrees, it is sensitive to the flame spectrum.
Comparator chip LM393 makes module readings stable.
Operating voltage 3.3V-5V.
Digital and Analog Output.
Power indicator and digital switch output indicator.
Interface Description (4-wire)VCC — 3.3V-5V voltage
GND — GND
DO — Digital output interface (0 or 1)
AO — Analog output interfaceQucik View -
Bosch BMP180 Barometer Pressure/Temperature/Altitude Sensor (Arduino Compatible)
₦ 2,800The BMP180 is a precision barometric pressure, temperature and altitude sensor from manufactured by Bosch. It is fully compatible with BMP085 in terms of firmware/software/interfacing. BMP180 can easily be configured to work with Arduino, ARM or PIC over I2C.
Specification
- 3-5V Logic and Power
- Pressure sensing range: 300-1100 hPa (9000m to -500m above sea level)
- Up to 0.03hPa / 0.25m resolution
- -40 to +85°C operational range, +-2°C temperature accuracy
- This board/chip uses I2C 7-bit address 0x77.
Arduino sample code: //www.haoyuelectronics.com/Attachment/GY-68/bmp085_arduino.zip
Datasheet: //cdn-shop.adafruit.com/datasheets/BST-BMP180-DS000-09.pdf
Product InformationBrandQucik View
Reviews
There are no reviews yet.