Only logged in customers who have purchased this product may leave a review.
DS18B20 Waterproof Temperature Sensor – Arduino Compatible
₦ 2,000
The DS18B20 allows you take temperature readings in water or oils within its specified temperature range.
DS18B20 Technical specs:
- Usable temperature range: -55 to 125°C (-67°F to +257°F)
- 9 to 12 bit selectable resolution
- Uses 1-Wire interface- requires only one digital pin for communication
- Unique 64 bit ID burned into chip
- Multiple sensors can share one pin
- ±0.5°C Accuracy from -10°C to +85°C
- Temperature-limit alarm system
- Query time is less than 750ms
- Usable with 3.0V to 5.5V power/data
Work with Arduino IDE on ESP8266 Wifi module to take temperature readings over the Internet: //iot-playground.com/blog/2-uncategorised/41-esp8266-ds18b20-temperature-sensor-arduino-ide
Related Products
-
Arduino Single Channel Relay Module 5V/10A
₦ 1,500This product is a 1-channel relay module board with LED indicators, It can be controlled by microcontrollers such as Arduino, AVR, PIC, ARM any other microcontroller operating at 5V.
With this relay you can easily control electrical appliances, lights, etc.
Features
-
- Diode protected input
- This relay module is 5V active low.
- It is an 1-channel relay interface board, which can be controlled directly by a wide range of microcontrollers.
- It is also able to control various appliances and other equipment with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Can be connected directly to microcontoller GPIO pins.
- Working status indicator lights are conducive to the safe use.
Qucik View -
-
Arduino CNC Shield V3.0
₦ 4,250Qucik View -
KY-031 Percussion Knock Sensor – Arduino Compatible
₦ 1,500This module is a knock sensor. It sends out signals which can be read with a microcontroller like Arduino. It is suitable for building projects like electronic drums, and sensing other kinds of vibration. It can be used in anti-theft projects and noise detection systems.
- Working voltage: 5V
- 3 Pinout: 5V, GND, Vout
- Size: 30*20mm
- Weight: 3g
Qucik View -
PN532 NFC and RFID Reader & Writer Module
₦ 9,000The PN532 is a widely used and supported NFC chip. This module will allow you to add NFC and RFID functionality to your project, allowing you to interact with phones, read and write NFC tags and RFID tags.
Features
- Typical Operating Distance have been updated to 5cm~7cm reading distance
- Work in NFC Mode or RFID reader/writer Mode
- RFID reader/writer supports:
- Mifare 1k, 4k, Ultralight, and DesFire cards
- ISO/IEC 14443-4 cards such as CD97BX, CD light, Desfire, P5CN072 (SMX)
- Innovision Jewel cards such as IRT5001 card
- FeliCa cards such as RCS_860 and RCS_854
- Plug and play, Arduino compatible
- Built in PCB Antenna, with 4cm~6cm communication distance
- On-board level shifter, Standard 5V TTL for I2C and UART, 3.3V TTL SPI
- Work as RFID reader/writer
- Work as 1443-A card or a virtual card
- Exchange data with other NFC devices such as smartphone
Package contains
- 1 PN532 NFC RFID Module
- 1 dupont cable Male-Male
- 1 Mifare S50 White Card
- 1 Mifare One S50 Key Ring
- 1 12P bent header pin
Arduino Library: //github.com/adafruit/Adafruit-PN532
Qucik View -
Micro SD Storage Board – Arduino Compatible
₦ 1,500This Micro SD card Adapter easibly adds Gigabytes of storage to your microcontroller project. Read and write from SD & SDHC cards via a microcontroller or Arduino board.
- Support Micro SD SDHC Card
- Power supply:4.5V – 5.5V, 3.3V voltage regulator circuit board
- Positioning holes: 4 M2 screws for mounting
- Control Interface: GND, VCC, MISO, MOSI, SCK, CS
Qucik View -
L298 H-Bridge Motor Driver – Arduino Compatible
₦ 4,000Basic attributes
Module name :Dual H-bridge motor driver module
Operating mode :H-bridge driver (dual)
Master chip :L298NLogic voltage :5V
Drive voltage :5V-35V
Logic Current :0mA-36mA
Drive current :2A (MAX single bridge)
Storage Temperature :-20 to 135Maximum Power :25W
Weight :30gExternal dimensions :43 * 43 * 27mmQucik View
Reviews
There are no reviews yet.