Only logged in customers who have purchased this product may leave a review.
R2323 to TTL Converter with Dupont Cable
₦ 1,600
This module suitable for any 3.3v or 5v microcontroller and Arduino
• Fully compatible with existing legacy COM port software
• Output signals: VDD, TXD, RXD, CTS, RTS, GND
• Power, TX, RX LED
• Power input: 3.3V or 5V
Package List:
1 * RS232 Serial To TTL Converter Module
4 * Dupont Jumping Cable
1 in stock
Related Products
-
LM2596 Adjustable Step-Down Power Module With Digital Display
₦ 2,000This board carries the multipurpose LM2596 power supply and allows you deliver a regulated voltage for any electronic device without the need for soldering or a multimeter. Simply set it and hook it up. The module displays the output voltage on a built in seven segment display.
Features
- 4V-40V Input Voltage.
- Continuously adjustable output voltage range of 1.25V-37V .
- Maximum output current up to 3A
- Switch toggles between viewing output or input voltage.
- Clear Seven Segment display for showing operating voltages
Qucik View -
DC Buzzer -3-24V
₦ 850These 3-24V buzzers allow you to give audible notification from your using any microcontroller or Arduino with or without a transistor.
- 3-24V Operating Voltage
- 90dB Sound Intensity
- Easy to connect cables
Qucik View -
5 Red LEDs + 5 Resistors
₦ 6005 Red LED with 5 330 Ohm resistors. With these, all that needs to be done is connect to Microcontroller or Arduino GPIO pins. Works fine for 5V or 3V circuits
Qucik View -
IR2110 + Free Socket
₦ 1,200The IR2110 is a high voltage, high speed power MOSFET and IGBT driver with independent high and low side referenced output channels. It is compatible with standard CMOS or LSTTL output, down to 3.3V logic.The floating channel can be used to drive an N-channel power MOSFET or IGBT in the high side configuration which operates up to 500 or 600 Volts.
It can be used to in inverter, solar and other power based projects to control MOSFET transistors or IGBT devices.
Features
- Floating channel designed for bootstrap operation Fully operational to +500V or +600V
- Gate drive supply range from 10 to 20V
- Undervoltage lockout for both channels
- 3.3V logic compatible Separate logic supply range from 3.3V to 20V Logic and power ground ±5V offset
- CMOS Schmitt-triggered inputs with pull-down
- Cycle by cycle edge-triggered shutdown logic
- Matched propagation delay for both channels
- Outputs in phase with inputs
Qucik View -
3.3V-5V TXS0108E 8 Channel Bidirectional Logic Level Converter
₦ 950This chip allow easy conversion between logic levels allowing easy interfacing of Modules or other integrated circuits to a microcontroller or Arduino system.
- 1.2 V to 3.6 V on A Port and 1.65 to 5.5 V on B Port
- Output Enable Function Using OE pin
- VCCA connects to lower logic level eg 3.3V
- VCCB connects to higher logic level eg 5V
- When Ax has TTL 3.3V input, Bx will get TTL 5V output
- When Bx has TTL 5V input, Ax will get TTL 3.3V output
- NO direction control required
Example applications are Arduino to GSM connections, 3.3V SPI/I2C module connection to 5V system, UART interfacing between systems operating at different voltages
Qucik View -
LCR-T4 Transistor, Diode, Triode Capacitance Meter
₦ 8,000The LCR-T4 is a multi-function meter for testing resistors, capacitors, diodes, transistors, mos-tubes, inductors.
Qucik View
Reviews
There are no reviews yet.