• 0 out of 5

    8-Channel Digital Capacitive Switch Touch Sensor Module For Arduino – TTP226


    A capacitive touch module which sends out signals on contact, it can be interfaced to an Arduino or any microcontroller. This module can be used to build all kinds of interesting projects from access control, home automation, automotive projects etc

    • Onboard TTP226 capacitive 8 keys touch sensor IC
    • Onboard 8 channel level status indicator
    • Working voltage: 2.4V-5.5V
    Qucik View
  • 0 out of 5

    ADXL335 3-Axis Analog Output Accelerometer Sensor


    The ADXL335 3-Axis Analog Accelerometer is excellent for your drone and motion sensing projects. With a very simple 3-axis analog output, it has a minimal I/O requirement.

    • 3-axis sensing
    • Small, low-profile package
    • Low power – 350 μA (typical)
    • Single-supply operation
    • 1.8 V to 3.6 V

    Can withstand up to 10,000 g shock

    Qucik View
  • 0 out of 5

    Bosch BMP180 Barometer Pressure/Temperature/Altitude Sensor (Arduino Compatible)


    The BMP180 is a precision barometric pressure, temperature and altitude sensor from manufactured by Bosch. It is fully compatible with BMP085 in terms of firmware/software/interfacing. BMP180 can easily be configured to work with Arduino, ARM or PIC over I2C.


    • 3-5V Logic and Power
    • Pressure sensing range: 300-1100 hPa (9000m to -500m above sea level)
    • Up to 0.03hPa / 0.25m resolution
    • -40 to +85°C operational range, +-2°C temperature accuracy
    • This board/chip uses I2C 7-bit address 0x77.


    Arduino sample code: //www.haoyuelectronics.com/Attachment/GY-68/bmp085_arduino.zip

    Datasheet: //cdn-shop.adafruit.com/datasheets/BST-BMP180-DS000-09.pdf



    Product Information


    Qucik View
  • 0 out of 5

    DHT22 Temperature and Humidity Sensor


    DHT-22 is a humidity and temperature sensor with read out over single wire digital interface. The sensor is already calibrated and doesn’t need extra components so you can measure relative humidity and temperature right away.

    • 3 to 5V power and I/O
    • 2.5mA max current use during conversion (while requesting data)
    • Good for 0-100% humidity readings with 2-5% accuracy
    • Good for -40 to 80°C temperature readings ±0.5°C accuracy
    • No more than 0.5 Hz sampling rate (once every 2 seconds)



    Qucik View
  • 0 out of 5

    Digital Capacitive Touch Sensor – TTP223B


    This device allows you to add touch functionality to your designs. It can be easily interfaced with an Arduino or other microcontroller GPIO pins.


    • Operating Voltage: 2-5V
    • Chip: TTP223B
    • Response Time: 60-220ms
    • PCB Size: 28x20mm
    • Fully Arduino Compatible
    Qucik View
  • 0 out of 5

    DS18B20 Waterproof Temperature Sensor – Arduino Compatible


    The DS18B20 allows you take temperature readings in water or oils within its specified temperature range.

    DS18B20 Technical specs:

    • Usable temperature range: -55 to 125°C (-67°F to +257°F)
    • 9 to 12 bit selectable resolution
    • Uses 1-Wire interface- requires only one digital pin for communication
    • Unique 64 bit ID burned into chip
    • Multiple sensors can share one pin
    • ±0.5°C Accuracy from -10°C to +85°C
    • Temperature-limit alarm system
    • Query time is less than 750ms
    • Usable with 3.0V to 5.5V power/data

    Work with Arduino IDE on ESP8266 Wifi module to take temperature readings over the Internet: //iot-playground.com/blog/2-uncategorised/41-esp8266-ds18b20-temperature-sensor-arduino-ide


    Qucik View
  • 0 out of 5

    F249 Infrared Motor Speed Sensor Module

    Qucik View
  • 0 out of 5

    HB100 Motion Detection Microwave Sensor Module


    This is a X-Band Bi-Static Doppler transceiver module. This module can be used to detect motion in projects relating to home automation, automatic doors, alarm systems and even vehicle speed detection.


    Transmission frequency: 10.525 GHz
    Frequency Setting Accuracy: 3MHz
    Output power (minimum): 13dBm EIRP
    Operating voltage: 5V 0.25V
    Operating Current (CW): 60mA max., 37mA typical
    harmonic emission: <-10dBm
    Pulse mode:
    Averagecurrent (5% DC): 2mA
    Pulse Width (Min.): 5uSec
    load cycles (Min.): 1%

    Qucik View
  • 0 out of 5

    Infra-Red Flame Sensor


    This module is sensitive to the flame and radiation. It also can detect ordinary light source in the range of of a wavelength 760nm-1100 nm. It can be used as a flame alarm or in fire fighting robots.


    Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm.
    Detection range: up to 100 cm.
    Adjustable detection range.
    Detection angle about 60 degrees, it is sensitive to the flame spectrum.
    Comparator chip LM393 makes module readings stable.
    Operating voltage 3.3V-5V.
    Digital and Analog Output.
    Power indicator and digital switch output indicator.
    Interface Description (4-wire)

    VCC — 3.3V-5V voltage
    GND — GND
    DO  — Digital output interface (0 or 1)
    AO  — Analog output interface

    Qucik View
  • 0 out of 5

    KY-031 Percussion Knock Sensor – Arduino Compatible


    This module is a knock sensor. It sends out signals which can be read with a microcontroller like Arduino. It is suitable for building projects like electronic drums, and sensing other kinds of vibration. It can be used in anti-theft projects and noise detection systems.


    • Working voltage: 5V
    • 3 Pinout: 5V, GND, Vout
    • Size: 30*20mm
    • Weight: 3g


    Qucik View
  • 0 out of 5

    LM35 Temperature Sensor


    The LM35 is a  precision integrated-circuit temperature sensor with an output voltage linearly-proportional to the Centigrade temperature. The very popular LM35 temperature sensor is displays 0.1V to 1°C and can be interfaced to any Arduino or microcontroller ADC with no external components




    • Calibrated Directly in Celsius (Centigrade)
    • Linear + 10-mV/°C Scale Factor
    • 0.5°C Ensured Accuracy (at 25°C)
    • Rated for Full −55°C to 150°C Range
    • Suitable for Remote Applications
    • Low-Cost
    • Operates from 4 V to 30 V
    • Less than 60-µA Current Drain


    Can be used to measure temperature in different kinds of electronic projects


    Qucik View
  • 0 out of 5

    MC-38 Wired Door & Window Sensor Module


    This door/window sensor modules are useful in detecting the state of doors, windows, drawers or cupboards. It can be easily interfaced directly to a microcontroller or an Arduino.

    • Normally open reed switch
    • Easily installed on doors, windows and drawers with screws
    • Rated current: 100 mA max
    • Rated voltage: 100VDC max
    • 15mm maximum operating space.
    Qucik View