Only logged in customers who have purchased this product may leave a review.
Single Sided A4 Copper Clad PCB Board
₦ 1,500
These low cost Single-sided copper-clad printed circuit board made from paper-based material. They are very useful when making simple single sided prototype boards.
- Great for prototypes and short run PCB
- low-cost printed circuit board.
- Easy to drill and cut.
- Suitable etchant ferric chloride solution.
- 210 × 297mm
Related Products
-
Class D High Power Digital Amplifier Board – TDA7492 -2 x 50W
₦ 15,000A powerful amplifier with 50W output on 2 channels, this board allows a very powerful output to be delivered from a single rail power supply.
- Power supply: Single Supply 10-26V DC voltage
- The Maximum power: 50W per channel (8 Ohm)
- Mono power 100W (4 Ohms)
- Size: 57 mm * 70mm * 21 mm
Qucik View -
Arduino Single Channel Relay Module 5V/10A
₦ 1,500This product is a 1-channel relay module board with LED indicators, It can be controlled by microcontrollers such as Arduino, AVR, PIC, ARM any other microcontroller operating at 5V.
With this relay you can easily control electrical appliances, lights, etc.
Features
-
- Diode protected input
- This relay module is 5V active low.
- It is an 1-channel relay interface board, which can be controlled directly by a wide range of microcontrollers.
- It is also able to control various appliances and other equipment with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Can be connected directly to microcontoller GPIO pins.
- Working status indicator lights are conducive to the safe use.
Qucik View -
-
4 Channel 5V Relay Module
₦ 7,000This board is built specifically for the ESP8266 WiFi module. It allows you to control all kinds of devices over the Internet from the wildly popular ESP8266-01 Module. Simply power up and program the board.
- Board size: 45 * 28 mm
- Board function description:
- IN +, IN-: 5V power input;
- TX, RX, GND: Serial debug pin
Qucik View -
MP3 Decoder Board With Remote Control
₦ 3,500A highly integrated single-chip multimedia sound systems allows you to play MP3 files from a flash disk or SD card. It is also an FM player and can accept auxilliary input from a 3.5mm jack.
FEATURES
- Single decoding, Support the MP3 format music.
- Digital tube display
- Support the TF card.have the USB interface.
- Support FM radio, cable band (87.5MHZ-108.0MHZ);
- Support 5-10 meter distance infrared remote control operation
- Support for external audio input .LINE IN(AUX)
- key-press: VOL-/ AUTO / VOL+ / MODE;
- MODE key: in turn switches between USB/SD/FM/AUX.
Qucik View -
ARM STM32F103C8T6 Development Board
₦ 9,500This board is low cost ARM Microcontroller development board – STM32F103C8T6. The board is suitable for learners and professionals alike who want the 32-bit power of ARM Coretex-M3 32-bit core.
Code for it can be written using MirkroC ARM, Keil MDK, Eclipse GCC, and many more.
Easily load code into the chip via UART (check out our USB-UART converter) //www.konga.com/usb-to-uart-5-pin-cp2102-module-serial-converter-1988801
You DON’T need a programmer, flash using //cdn2.starkled.com/content/uploads/2012/11/Flash_Loader_Demonstrator_v2.5.0_Setup.exe
Features
- On-board Mini USB interface, you can give the board power supply and USB communication.
- On-board test indicator LED
- On-board reset button and power indicator LED
- On-board 100ma 3.3V Regulator
- All GPIO are led out and the names of the pins are marked
- After soldering the headers, you can directly plug the board onto the breadboard
Technical Specifications
- CPU Part Number: STM32F103C8T6
- Core: ARM 32 Cortex-M3 CPU.
- Debug mode: SWD (can be programmed with ST-LINK V2)
- CPU Internal Maximum Clock : 72MHz
- External Clock Source: 8MHz crystal
- 64K flash memory, 20K SRAM
- 2.0-3.6V power, I/O
Programming Instructions
- Set Boot Jumper-0 to 1
- Set Boot Jumper-1 to 0
- Connect USB-TTL Converter’s TX to PA10 on STM Board
- Connect USB-TTL Converter’s RX to PA9 on STM Board
- Give 3.3V power to STM board using USB TTL converter
- Press and release reset button once
- Launch STM Flash Loader, Select Port Name (where your usb ttl converter is connected)
- Select Parity as Even, Baudate as 115200, Echo Disabled and Timeout 10s
- Press Next, and follow on screen instructions to program, erase or read STM microcontroller
Qucik View -
Transciever & Adapter Board NRF2401+
₦ 6,000The ubiquitous NRF24L01+ Module which is capable of short and medium range transmission of up to 2Mbps operates at 3.3V. This can be inconvenient for most engineers. Therefore, we have bunduled the module together with an adapter board to make things much easier
Qucik View
Reviews
There are no reviews yet.