Only logged in customers who have purchased this product may leave a review.
USB to UART Cable – PL2303
₦ 1,500
The Prolific PL2303 USB-TTL serial converter cable allows you to interface to TTL level devices directly from your PC.
PINOUT
- Red: +5 V
- Black: GND
- Green: Tx
- White: Rx
3 in stock
Related Products
-
USB to UART 5- Pin CP2102 Module Serial Converter
₦ 2,500A MUST HAVE FOR EVERY ELECTRONICS AND EMBEDDED SYSTEMS ENGINEER
TALK DIRECTLY TO MICROCONTROLLERS, GSM MODULE, GPS MODULES, BLUETOOTH AND MANY MORE VIA UART/RS232
This is a USB 2.0 to 3.3V TTL UART 5 Pin CP 2102 Module Serial Converter
Connect MCU easily to your computer
Stable and reliable chip set CP2102 USB specifications
2.0 compliant with full-speed 12Mbps
Standard USB type A male and TTL 5 Pin connector
5 pins for TXD RXD GND 3.3V 5V.
All handshaking and modem interface signals.
Baud rate: 300bps to 1.5 Mbps.
Byte receive buffer: 640 byte transmit buffer.
Hardware or X-On/X-Off handshaking support.
Event character support Line break transmission.
USB suspend states supported via SUSPEND pins.
Temperature Range : -40 to + 85
Supports windows 98, Vista, Mac OS 9, Mac OS X & Linux 2.40
Qucik View -
Mini USB 5V USB to 3.3V DC Power Outlet
₦ 1,500This DC power outlet allows connectivity of power and data to electronic projects. It allows USB data pins (D+ and D-) to be connected to a USB capable microcontroller. It also carries a 3.3V regulator on board and allows 5V devices to be powered as well.
USB Input: 5V
DC power socket input: 5-12V
Output: 5V and 3.3V
Qucik View -
AVR Programmer USB-ASP
₦ 2,500USBasp is a USB in-circuit programmer for Atmel AVR controllers. No special drivers required.
Key Features:
- Read or write the microcontroller EEPROM, firmware.
- Support for Windows, Mac OS X and Linux (will work on Windows 8.1)
- 5 KB/sec maximum write speed
- Software controlled SCK option to support targets with low clock speed (< 1.5MHz)
Qucik View -
CP2102 MICRO USB to UART TTL Module
₦ 1,5005A constant current LED driver and charger for lithium-ion battery
· 3.3V and 5V voltage output
· Supports baud rates from 300bps ~ 1Mbps
On-chip voltage regulator output voltage 3.3V
Supports data formats for 8 data bits, 1 stop bit and parity bits
Connotation 512 byte receive buffer and 512 byte transmit buffer
Support for hardware or X-ON / X-OFF handshakeQucik View -
3V to 5V USB Output Charger Step up Power Module
₦ 1,000This module is used as a DC-DC booster, converting 3V to 5V. With the aid of this board, you can charge your mobile phones and power other kinds of USB devices from power sources with voltage as little as 1.5V such as batteries.
- Non-isolated step-up module (BOOST)
- Input voltage: 1-5V
- Output voltage: 5.1-5 .2 V
- Output Current: Rated 1A-1.5A
- Efficiency: Up to 96% (the higher the input voltage, the higher the efficiency)
- Switching frequency: 500KHz
- Output ripple: 30mV (MAX) 20M bandwidth (input 4V output 5.1V 1A)
- Voltage indication: LED lights with load (input voltage less than 2.7V LED indicator off)
- Operating Temperature: Industrial (-40°c to +85°c)
- Full load temperature rise: 30°c
- Quiescent Current: 130uA
- Load regulation: ± 1%
- Voltage regulation: ± 0.5%
- Dynamic response speed: 5% 200uS
- Short circuit protection: None (Please use the lithium battery with protection.)
Qucik View -
R2323 to TTL Converter with Dupont Cable
₦ 1,600This module suitable for any 3.3v or 5v microcontroller and Arduino
• Fully compatible with existing legacy COM port software
• Output signals: VDD, TXD, RXD, CTS, RTS, GND
• Power, TX, RX LED
• Power input: 3.3V or 5VPackage List:
1 * RS232 Serial To TTL Converter Module
4 * Dupont Jumping CableQucik View
Reviews
There are no reviews yet.