Only logged in customers who have purchased this product may leave a review.
Vibration Sensor Module
₦ 1,000
A vibration sensor can be used trigger a certain outcome whenever vibration occours. This may be an anti-theft alarm for cars, motorcycles or bicycles, or even buildings.
Features
- Operating voltage of 3.3 V to 5 V
- Digital Output (0 and 1)
- Adjustable sensitivity
- Mounting hole
- Power and digital output LED indicator
Pin Out.
- VCC: positive (3.3 – 5V)
- GND: connect power negative
- DO: digital signal output
- AO: Do not use
1 in stock
Related Products
-
Bosch BMP180 Barometer Pressure/Temperature/Altitude Sensor (Arduino Compatible)
₦ 1,500The BMP180 is a precision barometric pressure, temperature and altitude sensor from manufactured by Bosch. It is fully compatible with BMP085 in terms of firmware/software/interfacing. BMP180 can easily be configured to work with Arduino, ARM or PIC over I2C.
Specification
- 3-5V Logic and Power
- Pressure sensing range: 300-1100 hPa (9000m to -500m above sea level)
- Up to 0.03hPa / 0.25m resolution
- -40 to +85°C operational range, +-2°C temperature accuracy
- This board/chip uses I2C 7-bit address 0x77.
Arduino sample code: //www.haoyuelectronics.com/Attachment/GY-68/bmp085_arduino.zip
Datasheet: //cdn-shop.adafruit.com/datasheets/BST-BMP180-DS000-09.pdf
Product InformationBrandQucik View -
Infra-Red Flame Sensor
₦ 1,000This module is sensitive to the flame and radiation. It also can detect ordinary light source in the range of of a wavelength 760nm-1100 nm. It can be used as a flame alarm or in fire fighting robots.
Features
Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm.
Detection range: up to 100 cm.
Adjustable detection range.
Detection angle about 60 degrees, it is sensitive to the flame spectrum.
Comparator chip LM393 makes module readings stable.
Operating voltage 3.3V-5V.
Digital and Analog Output.
Power indicator and digital switch output indicator.
Interface Description (4-wire)VCC — 3.3V-5V voltage
GND — GND
DO — Digital output interface (0 or 1)
AO — Analog output interfaceQucik View -
Pulse Sensor -Arduino Compatible
₦ 4,500This pulse sensor measure heart rate by simly being in contact with a finger or earlobe.
- 3-5V Operation
- Pulse Sensor Board
- Coded Cable with Standard Male Headers
For a tutorials and sample code, visit: //pulsesensor.com/pages/code-and-guide
Qucik View -
W1219 Thermostat Temperature Controller Switch Module + Waterproof NTC Sensor Module
₦ 4,500A digital temperature controller module with dual LED display and an inbuilt relay module for control. The cut-off temperature is set with buttons on board
- Control Range:-50~110 Celsius
- Control Precision:0.1 Celsius
- Measuring Input: NTC10K waterproof sensor L=0.5m
- High Temperature Alarm:-49~110 Celsius
- Input Voltage: DC 12V
- Output Type: relay output 10A (max)
- Return Difference Setting:0.1~30 degree Celsius
- Delay Starting:0-10min
Qucik View -
Rain Sensor – Arduino Compatible
₦ 1,500This rain sensor can be used for all kinds of weather monitoring, and translated into digital output signals and analog. Humidity Detection Sensor Module Snow Rain raindrops Detection for Arduino
- Sensitivity can be adjusted via potentiometer LED lights up when there is no rain output is high; as soon as raindrop is detected, the output goes to ground level (0V).
- Connect to the microcontroller/Arduino ADC port to detect the size of the drops in the above rainfall. DO TTL digital outputs can also be connected to the microcontroller detects whether there is rain.
- Digital outputs (0 and 1) and analog AO voltage output; TTL-level output, TTL output valid signal is low. Driving capability 100MA so, can directly drive relays, buzzer or small fan.
Pin functions include:
- VCC(3V to 5V)
- GND
- AO (Analog Output)
- Digital Output (TTL levels)
Package Includes:
- Rain sensing pad
- Sensing PCB
- Dupont cable
Qucik View -
Pir Motion Sensor
₦ 2,000This PIR motion sensor detects live moving objects such as humans or pets. It produces a 3.3V output for (5-200 seconds) to indicate presence of live moving object. It can be used to control lights, security detection, home automation, etc
- 5-12V Operating Voltage
- 3.3 V /Low 0V
- Adjustable sensitiity
- Variable trigger length (5-200 seconds)
- Repeated trigger (L position) or Single trigger (H position) setting
Qucik View
Reviews
There are no reviews yet.