Only logged in customers who have purchased this product may leave a review.
ESP8266-01 WiFi Module

ESP8266-01 WiFi Module
₦ 3,000
The ESP8266 WiFi Module allows you to add Internet conncetivity to your next electronic project. It has a built-in TCP/IP protocol stack. AT commands are issued over UART. Fully Arduino friendly.
- 3.3V Operating Voltage
- 802.11 b/g/n
- Wi-Fi Direct (P2P), soft-AP
- Integrated TCP/IP protocol stack
- Integrated low power 32-bit CPU could be used as application processor
- SDIO 1.1 / 2.0, SPI, UART
- Arduino compatible library
AT Command Set
//cdn.sparkfun.com/datasheets/Wireless/WiFi/Command%20Doc.pdf
Out of stock
Related Products
-
0 out of 5
12V Relay Module – 10A –Pair
₦ 850This 6V Relay allows your to control loads with up to 10A consumption
Features:
-
- 6V Coil
- Maximum Load DC: 24V (DC) @ 10A
- Maximum Load AC: 240V (AC) @ 10A
- Maximum turn-on time: 10ms
- Maximum turn-off time: 5ms
- Easy through hole mounting arrangement
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
-
0 out of 5
A6 GSM & GPRS Module
₦ 8,500A module that supports dual-band GSM/GPRS network, available for GPRS and SMS. Comes ready to keep your project connected via phone calls, SMS, or the Internet.
- Working frequency: quad-band network, 850 / 900 / 1800 / 1900MHz
- Working voltage: 4.5~5.5V DC (On-board voltage regulator circuit supply power for A6 module)
- Working current: maximum of 2A
- Sleep current: 5mA
- Onboard Micro SIM card holder, you can install Micro SIM card
- Onboard Micro USB interface for external power supply
- Communication Interface: TTL serial port
- Baud rate: 115200bps and it can also be set by AT command.
- Interface logic voltage: 3.3V
- Make and answer phone calls using a headset and electret microphone.
- Send and receive SMS messages.
- Send and receive GPRS data (TCP/IP, HTTP, etc.)
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Arduino Double Channel Relay Module 5V/10A
₦ 2,000This product is a 2-channel relay module board with LED indicators, It can be controlled by microcontrollers such as Arduino, AVR, PIC, ARM any other microcontroller operating at 5V.
With this relay you can easily control electrical appliances, lights, etc.
Features
-
- Opto-isolated input
- This relay module is 5V active low.
- It is an 1-channel relay interface board, which can be controlled directly by a wide range of microcontrollers.
- It is also able to control various appliances and other equipment with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Can be connected directly to microcontoller GPIO pins.
- Working status indicator lights are conducive to the safe use.
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
-
0 out of 5
AT-09-BLE-Bluetooth-4-0-Module—HM-10-Compatible-6620015
₦ 4,000This Bluetooth 4.0 TTL transceiver module allows you to communicate with any gadget using the highly energy efficient Bluetooth 4.0 specification
Features
- Power input: 3.6V-6V DC(Can not higher than 6V)
- It’s easy to use and safely enclosed in a plastic sheath
- Bluetooth version: V4.0
- Default baud rate: 9600 (Adjustable baudrate)
- Default serial port setting: 9600, N, 8, 1
- Operates as slave or master.
- Ultra-low standby power consumption 90uA~400uA
- Coverage up to 60 meters
- Built in PCB antenna
- Size: 43mm x 15mm
Pinout- VCC: input power supply 3.3~6V, Prohibit more than 7V
- GND: Ground
- TX: transport
- RX: receive
- State: when bluetooth is connected , output “High level”, “no conntected” output “low level”
- en:when module is connected, give a high level to “EN”,the module will disconnected.
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
HB100 Motion Detection Microwave Sensor Module
₦ 3,500This is a X-Band Bi-Static Doppler transceiver module. This module can be used to detect motion in projects relating to home automation, automatic doors, alarm systems and even vehicle speed detection.
Feature
Transmission frequency: 10.525 GHz
Frequency Setting Accuracy: 3MHz
Output power (minimum): 13dBm EIRP
Operating voltage: 5V 0.25V
Operating Current (CW): 60mA max., 37mA typical
harmonic emission: <-10dBm
Pulse mode:
Averagecurrent (5% DC): 2mA
Pulse Width (Min.): 5uSec
load cycles (Min.): 1%Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Arduino Dual-axis XY Joystick Module
₦ 1,500A joystick module which can be interfaced with a microcontroller like Arduino. It can be used in your robotics projects
-
- Dual-axis XY Joystick Module for Arduino
- Size: 4 X 2.6 X 3.2CM
- 2 potentiometers for 2 axes
- 1 switch
- Working voltage: 5V
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
Reviews
There are no reviews yet.