Only logged in customers who have purchased this product may leave a review.
Arduino LilyPad – Atmega 328 Model
₦ 6,000
The LilyPad Arduino 328 Board is an Arduino based board designed for making wearable and e-textile type projects. It is fully Arduino compatible and has holes for easily sewing it into projects. LEDs, Sensors, buttons and so much more can be easily integrated.
Features:
- ATmega328 Microcontroller
- Operating Voltage 2.7-5.5 V
- Input Voltage 2.7-5.5 V
- Digital I/O Pins 14
- PWM Channels 6
- Analog Input Channels 6
- DC Current per I/O Pin 40 mA
- Flash Memory 16 KB (of which 2 KB used by bootloader)
- SRAM 1 KB
- EEPROM 512 bytes
- Clock Speed 8 MHz
2 in stock
Related Products
-
Arduino Mega
₦ 28,500The Arduino Mega is just the Arduino for when you need to bring the big guns out. It has 54 GPIO, 4 UART pins, 16 Analog inputs and more
Features
- Microcontroller ATmega2560
- Operating Voltage 5V
- Input Voltage (recommended) 7-12V
- Input Voltage (limits) 6-20V
- Digital I/O Pins 54 (of which 15 provide PWM output)
- Analog Input Pins 16
- DC Current per I/O Pin 40 mA
- DC Current for 3.3V Pin 50 mA
- Flash Memory 256 KB of which 8 KB used by bootloader
- SRAM 8 KB
- EEPROM 4 KB
- Clock Speed 16 MHz
- Resettable polyfuse that protects PC USB ports from shorts and overcurrent
Qucik View -
20 X 4 LCD Module – Arduino Compatible
₦ 5,000This 20 X 4 LCD Module allows you to fit in a lot more text than you can on the smaller 16X4. It is however fully compatible. It has the industry standard HD44780 LCD controller.
-
- 20X4 Characters
- 5V Operating voltage
- Fully pin and code compatible with 16X2, 16X1 LCDs
- Backlight
Qucik View -
-
Bosch BMP180 Barometer Pressure/Temperature/Altitude Sensor (Arduino Compatible)
₦ 1,500The BMP180 is a precision barometric pressure, temperature and altitude sensor from manufactured by Bosch. It is fully compatible with BMP085 in terms of firmware/software/interfacing. BMP180 can easily be configured to work with Arduino, ARM or PIC over I2C.
Specification
- 3-5V Logic and Power
- Pressure sensing range: 300-1100 hPa (9000m to -500m above sea level)
- Up to 0.03hPa / 0.25m resolution
- -40 to +85°C operational range, +-2°C temperature accuracy
- This board/chip uses I2C 7-bit address 0x77.
Arduino sample code: //www.haoyuelectronics.com/Attachment/GY-68/bmp085_arduino.zip
Datasheet: //cdn-shop.adafruit.com/datasheets/BST-BMP180-DS000-09.pdf
Product InformationBrandQucik View -
Arduino Uno
₦ 12,500The Arduino Uno R3 is a microcontroller board based on the ATmega328. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
The Uno differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip.
Additional features coming with the R3 version are:
ATmega16U2 instead 8U2 as USB-to-Serial converter.
1.0 pinout: added SDA and SCL pins for TWI communication placed near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board and the second one is a not connected pin, that is reserved for future purposes.
stronger RESET circuit.
“Uno” means “One” in Italian and is named to mark the upcoming release of Arduino 1.0. The Uno and version 1.0 will be the reference versions of Arduino, moving forward. The Uno is the latest in a series of USB Arduino boards, and the reference model for the Arduino platform.Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limit) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) PWM Digital I/O Pins 6 Analog Input Pins 6 DC Current per I/O Pin 20 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB of which 0.5 KB used by bootloader SRAM 2 KB EEPROM 1 KB Clock Speed 16 MHz LED_BUILTIN 13 Length 68.6 mm Width 53.4 mm Weight 25 g Qucik View -
ARM STM32F103C8T6 Development Board
₦ 11,000This board is low cost ARM Microcontroller development board – STM32F103C8T6. The board is suitable for learners and professionals alike who want the 32-bit power of ARM Coretex-M3 32-bit core.
Code for it can be written using MirkroC ARM, Keil MDK, Eclipse GCC, and many more.
Easily load code into the chip via UART (check out our USB-UART converter) //www.konga.com/usb-to-uart-5-pin-cp2102-module-serial-converter-1988801
You DON’T need a programmer, flash using //cdn2.starkled.com/content/uploads/2012/11/Flash_Loader_Demonstrator_v2.5.0_Setup.exe
Features
- On-board Mini USB interface, you can give the board power supply and USB communication.
- On-board test indicator LED
- On-board reset button and power indicator LED
- On-board 100ma 3.3V Regulator
- All GPIO are led out and the names of the pins are marked
- After soldering the headers, you can directly plug the board onto the breadboard
Technical Specifications
- CPU Part Number: STM32F103C8T6
- Core: ARM 32 Cortex-M3 CPU.
- Debug mode: SWD (can be programmed with ST-LINK V2)
- CPU Internal Maximum Clock : 72MHz
- External Clock Source: 8MHz crystal
- 64K flash memory, 20K SRAM
- 2.0-3.6V power, I/O
Programming Instructions
- Set Boot Jumper-0 to 1
- Set Boot Jumper-1 to 0
- Connect USB-TTL Converter’s TX to PA10 on STM Board
- Connect USB-TTL Converter’s RX to PA9 on STM Board
- Give 3.3V power to STM board using USB TTL converter
- Press and release reset button once
- Launch STM Flash Loader, Select Port Name (where your usb ttl converter is connected)
- Select Parity as Even, Baudate as 115200, Echo Disabled and Timeout 10s
- Press Next, and follow on screen instructions to program, erase or read STM microcontroller
Qucik View -
Arduino Pro Mini
₦ 6,000The Arduino Pro mini is an Arduino board perfect for small applications that need to pack a bang. It has the same microcontroller as the Arduino Uno.
- ATmega328 Microcontroller
- 5 – 12V Supply Voltage
- 16 MHz
- 14 Digital GPIO Pins
- PWM Pins 6
- UART 1
- SPI 1
- I2C 1
- Analog Input Pins 6
- External Interrupts 2
- DC Current per I/O Pin 40 mA
- Flash Memory 32KB (2 KB used by bootloader)
- SRAM 2 KB
- EEPROM 1 KB
A USB to UART converter is needed to program it.
Qucik View
Reviews
There are no reviews yet.