Only logged in customers who have purchased this product may leave a review.
ST-Link V2 STM8/STM32 Programmer & Emulator
₦ 10,000
This pocket friendly USB programmer and debugger allows STM8 and STM32 (ARM) microcontrollers to be programmed and debugged.
Product Features:
- Support for all the STM8 devices via SWIM interface
- Support for all STM32 devices with SWD interface
- Debugging : run at full-speed, single-stepped, breakpoints, viewing variables and registers, etc.
- Programming : supports FLASH ROM, EEPROM, AFR, etc.
- Onboard 500mA self-recovery fuse to avoid harming by short circuit
- Dual voltage output (3.3V/5V), easy for debugging/programming
- Standard USB interface to PC
- USB2.0 combined with SWIM/SWD interfaces : quick response for debugging & fast speed for programming
- Upgradable firmware
The board supports any of the following softwares:
- ST – LINK Utility 2.0 and above
- STVD 2 and above
- STVP 3.2.3 and above
- IAR EWARM V6.20 and above
- IAR EWSTM8 V1.30 and above
- KEIL RVMDK V4.21 and above
- ATOLLIC
- TASKING
Related Products
-
8-Bit Microcontroller – PIC18F452
₦ 3,500High-Performance 8 bit Microcontrollers.
Features inlude:
-
- Capable 40MHz operation (10 Million Instructions per Second)
- 32K Flash Memory
- 1.5kB RAM
- 8X8 Hardware Multiplier
- UART Module
- 10bit ADC Module
- ICSP Programming
- PWM Module
- I2C Module
Qucik View -
-
Pickit3 Microcontroller Programmer – Debugger
₦ 30,000Pickit3 PIC microcontroller programmer and debugger. Included in the pack are
- PICkit3 programmer
- USB Cable
- ICSP Connector cable
This programmer can load code an debug all PIC12, PIC16, PIC18, PIC24, PIC32, DSPIC family of microcontrollers.
Qucik View -
High-Speed USB SPI Programmer – EZP2010
₦ 12,000This programmer can read and write the BIOS chips of a DVD,TV,etc
- USB 2.0 interface, the speed is 12Mbps.
- Auto detect chip modules.
- Auto select power voltage.
- Auto off-line chip copy.
- Software and firmware update.
- Support chip of 25 FLASH, 24 EEPROM, 25 EEPROM, 93 EEPROM, etc
Qucik View -
AVR Programmer USB-ASP
₦ 9,500USBasp is a USB in-circuit programmer for Atmel AVR controllers. No special drivers required.
Key Features:
- Read or write the microcontroller EEPROM, firmware.
- Support for Windows, Mac OS X and Linux (will work on Windows 8.1)
- 5 KB/sec maximum write speed
- Software controlled SCK option to support targets with low clock speed (< 1.5MHz)
Qucik View -
STM8S103F3P6 Mini Dev Board
₦ 1,500This STM8S103 Minimum development board is suitable for STM8 enthusiast. It packs a lot of power in a very small package.
- 16 MHz advanced STM8 core with Harvard architecture and 3-stage pipeline
- RAM: 1 Kbyte
- 2.95 to 5.5 V operating voltage
- Internal, user-trimmable 16 MHz RC
- Internal low-power 128 kHz RC
- On-board 5V Regulator.
- Can be powered by 5V USB port
- Support SWIM programming.
- 2 Built-In LEDs Power and GPIO on pin PD3 (This should flash when you power it up)
- On board reset button
- 8K Flash Memory
- 640 bytes EEPROM
- Reflash up to 10K times
Qucik View -
2 x 2032 Coin Cell Battery Holder – 6V Output with On & Off switch
₦ 2,000This battery holder with On/Off Switch carries two CR2032 coin cells with 30cm black and red leads! Perfect for robotic ,electronic and communication projects
- Very compact design
- Holds Two CR2032 coin batteries
- High Quality Plastic
- Perfect for soldering
- On and Off Switch
Qucik View
Reviews
There are no reviews yet.