Only logged in customers who have purchased this product may leave a review.
RS-485 to TTL Converter Module
₦ 1,500
This RS485 to TTL Module allows you to communicate to an RS-485 device, module or another microcontroller at over 1Mbps from over 1km away! This RS485 transciever can be easily interfaced to a microcontroller or Arduino
- Uses MAX485 integrated circuit
- Pinout DI,DE,RE,RD signals
- 5 Volt Operation
Related Products
-
LM2596 Adjustable Step-Down Power Module With Digital Display
₦ 3,500This board carries the multipurpose LM2596 power supply and allows you deliver a regulated voltage for any electronic device without the need for soldering or a multimeter. Simply set it and hook it up. The module displays the output voltage on a built in seven segment display.
Features
- 4V-40V Input Voltage.
- Continuously adjustable output voltage range of 1.25V-37V .
- Maximum output current up to 3A
- Switch toggles between viewing output or input voltage.
- Clear Seven Segment display for showing operating voltages
Qucik View -
150W DC-DC Boost Converter – 10-32V to 12-35V
₦ 4,500The module is a non-isolated step-up module (BOOST)
- Dimensions: 65 * 56.5 * 23 (length * width * high) (mm)
- Input voltage :10-32V
- Output voltage: 12-35V (adjustable)
- Output Current: 6A (MAX)
- Input Current: 10A (MAX) (Please enhance heat dissipation if more than 10A)
- Output power: natural cooling 100W (MAX), enhance heat dissipation 150W (MAX)
- Conversion efficiency: 94% (measured at Input 16V, output 19V 2.5A)
- Output Ripple: 2% (MAX) 20M-bandwidth
- Operating Temperature: Industrial (-40c to +85c) (ambient temperature exceeds 40c, lower power use, or to enhance heat dissipation)
- Full load temperature rise: 45c
- No-load current: 25mA typical
- Voltage regulation: 0.5%
- Dynamic response speed: 5% 200uS
Applications:
-
- Easily power an laptop from a 12V battery
- Power 24V loads from a simple 12V battery
- Boost up solar power for more advanced applications
Qucik View -
3.3V-5V TXS0108E 8 Channel Bidirectional Logic Level Converter
₦ 2,000This chip allow easy conversion between logic levels allowing easy interfacing of Modules or other integrated circuits to a microcontroller or Arduino system.
- 1.2 V to 3.6 V on A Port and 1.65 to 5.5 V on B Port
- Output Enable Function Using OE pin
- VCCA connects to lower logic level eg 3.3V
- VCCB connects to higher logic level eg 5V
- When Ax has TTL 3.3V input, Bx will get TTL 5V output
- When Bx has TTL 5V input, Ax will get TTL 3.3V output
- NO direction control required
Example applications are Arduino to GSM connections, 3.3V SPI/I2C module connection to 5V system, UART interfacing between systems operating at different voltages
Qucik View -
Bi-Directional 4 Channel Logic Level Converter
₦ 1,500This tiny logic level shifter features four bidirectional channels, allowing for safe and easy communication between devices operating at different logic levels. It can convert signals as low as 1.5 V to as high as 18 V and vice versa, and its four channels are enough to support most common bidirectional and unidirectional digital interfaces, including I²C, SPI, and asynchronous TTL serial.
Qucik View -
Female-Female Dupont Jumper Cables
₦ 2,000These male to male dupont jumper cables will help you easily connect things up, especially modules and sensors
- 40 Colored dupont cables
- Length: 20cm
- 1p-1p pin header, Female to Female.
- 2.54mm/1 inch spacing spacing pin headers
- Easily connect modules and sensors
Qucik View -
16×2 LCD Module
₦ 3,00016X2 LCD Module with Blue backlight
-
- Easily controlled from any microcontroller
- 4/8 bit communication mode
- Special character mode
- Blue backlight
- HD44780 Controller
Qucik View -
Reviews
There are no reviews yet.