Only logged in customers who have purchased this product may leave a review.
MQ-3 – Alcohol Gas Sensor – Arduino Compatible
₦ 3,000
This sensor allows you to detect alcohol concentration levels. Use only one analog pin to microcontroller for detection
- 5V Operation
- Highly sensitive to alcohol
- Fast response time
Example Application: Breathalyzer,Alcohol concentration detector.
Related Products
-
Arduino Mega
₦ 28,500The Arduino Mega is just the Arduino for when you need to bring the big guns out. It has 54 GPIO, 4 UART pins, 16 Analog inputs and more
Features
- Microcontroller ATmega2560
- Operating Voltage 5V
- Input Voltage (recommended) 7-12V
- Input Voltage (limits) 6-20V
- Digital I/O Pins 54 (of which 15 provide PWM output)
- Analog Input Pins 16
- DC Current per I/O Pin 40 mA
- DC Current for 3.3V Pin 50 mA
- Flash Memory 256 KB of which 8 KB used by bootloader
- SRAM 8 KB
- EEPROM 4 KB
- Clock Speed 16 MHz
- Resettable polyfuse that protects PC USB ports from shorts and overcurrent
Qucik View -
Arduino Nano
₦ 7,500The Arduino Nano is a full featured breadboard-friendly Arduino board. It is based on an Atmega 328 microcontroller. Fully programmable with Arduino IDE
Key Features:
- 5V Operating Voltage
- 7-12 Volt Unregulated Supply Voltage
- 8 Analog Input Pins
- 14 Digital I/O Pins
- 32kB Flash Memory (2kB Bootloader)
- 1kB RAM
- 512 Bytes EEPROM
- UART
- SPI
- PWM
Qucik View -
PN532 NFC and RFID Reader & Writer Module
₦ 6,000The PN532 is a widely used and supported NFC chip. This module will allow you to add NFC and RFID functionality to your project, allowing you to interact with phones, read and write NFC tags and RFID tags.
Features
- Typical Operating Distance have been updated to 5cm~7cm reading distance
- Work in NFC Mode or RFID reader/writer Mode
- RFID reader/writer supports:
- Mifare 1k, 4k, Ultralight, and DesFire cards
- ISO/IEC 14443-4 cards such as CD97BX, CD light, Desfire, P5CN072 (SMX)
- Innovision Jewel cards such as IRT5001 card
- FeliCa cards such as RCS_860 and RCS_854
- Plug and play, Arduino compatible
- Built in PCB Antenna, with 4cm~6cm communication distance
- On-board level shifter, Standard 5V TTL for I2C and UART, 3.3V TTL SPI
- Work as RFID reader/writer
- Work as 1443-A card or a virtual card
- Exchange data with other NFC devices such as smartphone
Package contains
- 1 PN532 NFC RFID Module
- 1 dupont cable Male-Male
- 1 Mifare S50 White Card
- 1 Mifare One S50 Key Ring
- 1 12P bent header pin
Arduino Library: //github.com/adafruit/Adafruit-PN532
Qucik View -
L298 H-Bridge Motor Driver – Arduino Compatible
₦ 3,000Basic attributes
Module name :Dual H-bridge motor driver module
Operating mode :H-bridge driver (dual)
Master chip :L298NLogic voltage :5V
Drive voltage :5V-35V
Logic Current :0mA-36mA
Drive current :2A (MAX single bridge)
Storage Temperature :-20 to 135Maximum Power :25W
Weight :30gExternal dimensions :43 * 43 * 27mmQucik View -
SCT-013 Non-invasive 100A Current Transformer (CT) -Arduino Compatible
₦ 7,500This current transformer allows you to easily measure to current running through a wire without tampering with the setup, simply pass the wire through or open up and clip around the wire.
Can be used for any of the following applications: Measurment and protection circuits, AC motors, lighting, air compressors, remote monitoring, Energy meters,etc
Features:
- Measures up to 100A
- Core material: ferrite
- Non-linearity 3%(10%-120% rated input current)
- 1.5m leading wire, with 3.5mmplug standard output.
- Two form of output current, voltage (voltage output built-in the burden resistor).
- Opening size:13mmx13mm
- Safety indicators: Dielectric strength 6000V AC/1min
- Meet UL94-V0 flame retardant properties
- Operating Temperature: -25 C ~ +70 C
Qucik View -
Arduino Pro Mini
₦ 6,000The Arduino Pro mini is an Arduino board perfect for small applications that need to pack a bang. It has the same microcontroller as the Arduino Uno.
- ATmega328 Microcontroller
- 5 – 12V Supply Voltage
- 16 MHz
- 14 Digital GPIO Pins
- PWM Pins 6
- UART 1
- SPI 1
- I2C 1
- Analog Input Pins 6
- External Interrupts 2
- DC Current per I/O Pin 40 mA
- Flash Memory 32KB (2 KB used by bootloader)
- SRAM 2 KB
- EEPROM 1 KB
A USB to UART converter is needed to program it.
Qucik View
Reviews
There are no reviews yet.