Only logged in customers who have purchased this product may leave a review.
Mini Submersible Water Pump
₦ 2,000
This simple DC submersible pump allows you to pump water at a rate of up to 120L/H and operates at 3-5V
Features
- DC Voltage: 3-6V
- Maximum lift:40-110cm / 15.75″-43.4″
- Flow rate:80-120L/H
- Outside diameter of water outlet: 7.5mm / 0.3″
- Inside diameter of water outlet: 4.7mm / 0.18″
- Diameter:Approx. 24mm / 0.95″
- Length:Approx. 45mm / 1.8″
- Height:Approx. 33mm / 1.30″
- Plastic
- Driving mode: Brushless DC Motor
- Continuous working life of 500 hours
Out of stock
Related Products
-
SMD to DIP Adapter (QFP, TQFP, FQFP, LQFP)
₦ 1,000This SMD Adapter let’s you solder 0.5mm and 0.8mm SMD Integrated Circuits (IC) such as Atmel, MSP, STC and Microchip microcontrollers
- 0.5mm and 0.8mm on opposite sides
- 32-100 pin SMD components
- 0.8mm side allows mounting of 32 to 64 pin components
- 0.5mm side allows mounting of 32 to 100 pin components
- Applicable to common package: QFP, TQFP, FQFP, LQFP, etc.
- Size: 38 * 46mm
Qucik View -
NEMA 17 Motor and Coupling
₦ 9,000This stepper motor and coupling pair are perfect for robotics, 3D printer and other kinds of high precision projects. 1.8° per step smooth motion. It also has a solid holding torque.
- 5mm Shaft
- 5mm X 5mm Coupling
- 200 steps/rev
- 12V Operating Voltage
- 350mA (Max Current)
- 1.8 degrees per step
- Bipolar stepper motor
- 20 N*cm, 2 Kg*cm holding torque per phase
- 35 ohms per winding
- 42mm X 42mm square body -M3 Mounting Screws
Qucik View -
DC Buzzer -3-24V
₦ 1,000These 3-24V buzzers allow you to give audible notification from your using any microcontroller or Arduino with or without a transistor.
- 3-24V Operating Voltage
- 90dB Sound Intensity
- Easy to connect cables
Qucik View -
L298 H-Bridge Motor Driver – Arduino Compatible
₦ 1,800Basic attributes
Module name :Dual H-bridge motor driver module
Operating mode :H-bridge driver (dual)
Master chip :L298NLogic voltage :5V
Drive voltage :5V-35V
Logic Current :0mA-36mA
Drive current :2A (MAX single bridge)
Storage Temperature :-20 to 135Maximum Power :25W
Weight :30gExternal dimensions :43 * 43 * 27mmQucik View -
5V 30A Single Channel Relay
₦ 2,200This product is a 1-channel relay module board with LED indicators, It can be controlled by microcontrollers such as Arduino, AVR, PIC, ARM any other microcontroller operating at 5V.
With this relay you can easily control electrical appliances, lights, etc.
Features:
- 5V Operation
- The static current:5mA
- Working current:190mA
- Trigger current:2-4mA
Module interface specifications:
-
- DC+ : DC power supply positive pole
- DC- :DC power supply negative pole
- IN : signal triggering pin
- JD+ : relay control voltage positive
- JD- : relay control voltage negative
- It is an 1-channel relay interface board, which can be controlled directly by a wide range of microcontrollers.
- It is also able to control various appliances and other equipment with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Can be connected directly to microcontoller GPIO pins.
- Working status indicator lights are conducive to the safe use.
Qucik View -
MAX232 + Free Socket and Capacitors
₦ 1,000The MAX232 is an integrated circuit which converts signals from a TIA-232 (RS-232) serial port to signals suitable for use in TTL-compatible digital logic circuits such as microcontrollers. The MAX232 is a dual transmitter / dual receiver that typically is used to convert the RX, TX, CTS, RTS signals.
MAX232.
Features
- Meets or Exceeds TIA/EIA-232-F and ITU Recommendation V.28
- Operates From a Single 5-V Power Supply With 1.0-F Charge-Pump Capacitors
- Operates Up To 120 kbit/s
- Two Drivers and Two Receivers sot that up to two devices can use the same chip or flow control lines such as DTR and CTS.
- ±30-V Input Levels
- Low Supply Current… 8 mA Typical
- ESD Protection
Qucik View
Reviews
There are no reviews yet.