Only logged in customers who have purchased this product may leave a review.
LM2596 DC-DC Step-Down Power Supply Module
₦ 2,250
Description:
DC-DC Buck Converter Step Down Module LM2596 Power Supply is a step-down(buck) switching regulator, capable of driving a 3-A load with excellent line and load regulation.
The LM2596 series operates at a switching frequency of 150 kHz, thus allowing smaller sized filter components than what would be required with lower frequency switching regulators
Specifications:
- Input voltage:3-40V
- Output voltage:1.5-35V(Adjustable)
- Output current: Rated current is 2A, maximum 3A(Additional heatsink is required)
- Module Properties: non-isolated constant voltage module
- Rectification: non-synchronous rectification
- Short circuit protection: current limiting, since the recovery
- Switching Frequency: 150KHz
Related Products
-
A6 GSM & GPRS Module
₦ 13,000A module that supports dual-band GSM/GPRS network, available for GPRS and SMS. Comes ready to keep your project connected via phone calls, SMS, or the Internet.
- Working frequency: quad-band network, 850 / 900 / 1800 / 1900MHz
- Working voltage: 4.5~5.5V DC (On-board voltage regulator circuit supply power for A6 module)
- Working current: maximum of 2A
- Sleep current: 5mA
- Onboard Micro SIM card holder, you can install Micro SIM card
- Onboard Micro USB interface for external power supply
- Communication Interface: TTL serial port
- Baud rate: 115200bps and it can also be set by AT command.
- Interface logic voltage: 3.3V
- Make and answer phone calls using a headset and electret microphone.
- Send and receive SMS messages.
- Send and receive GPRS data (TCP/IP, HTTP, etc.)
Qucik View -
LM2596 Adjustable Step-Down Power Module With Digital Display
₦ 3,500This board carries the multipurpose LM2596 power supply and allows you deliver a regulated voltage for any electronic device without the need for soldering or a multimeter. Simply set it and hook it up. The module displays the output voltage on a built in seven segment display.
Features
- 4V-40V Input Voltage.
- Continuously adjustable output voltage range of 1.25V-37V .
- Maximum output current up to 3A
- Switch toggles between viewing output or input voltage.
- Clear Seven Segment display for showing operating voltages
Qucik View -
Ethernet Module – ENC28J60
₦ 10,000This module allows you to add Ethernet connectivity to your projects. Based on the popular Microchip’s ENC28J60, this module will easily interface with any Microcontroller or Arduino board allowing Internet Connectivity via the Ethernet..
- Up to 10Mbps
- 5V Tolerant I/O pins
- Fully IEEE 803.2 Standards compatible
Qucik View -
Arduino Buzzer Module
₦ 1,500This module allows you to produce a rich and loud sound from your microcontroller.
- 3.3 V to 5 V Operating Voltage
- 3V to 5V Control
- Works without the need of a separate transistor
- Mounting Hole
Pin Out
-
- VCC (3.3 V to 5 V)
- GND
- I/O Control
Qucik View -
AT-09-BLE-Bluetooth-4-0-Module—HM-10-Compatible-6620015
₦ 10,000This Bluetooth 4.0 TTL transceiver module allows you to communicate with any gadget using the highly energy efficient Bluetooth 4.0 specification
Features
- Power input: 3.6V-6V DC(Can not higher than 6V)
- It’s easy to use and safely enclosed in a plastic sheath
- Bluetooth version: V4.0
- Default baud rate: 9600 (Adjustable baudrate)
- Default serial port setting: 9600, N, 8, 1
- Operates as slave or master.
- Ultra-low standby power consumption 90uA~400uA
- Coverage up to 60 meters
- Built in PCB antenna
- Size: 43mm x 15mm
Pinout- VCC: input power supply 3.3~6V, Prohibit more than 7V
- GND: Ground
- TX: transport
- RX: receive
- State: when bluetooth is connected , output “High level”, “no conntected” output “low level”
- en:when module is connected, give a high level to “EN”,the module will disconnected.
Qucik View -
Arduino Double Channel Relay Module 5V/10A
₦ 3,500This product is a 2-channel relay module board with LED indicators, It can be controlled by microcontrollers such as Arduino, AVR, PIC, ARM any other microcontroller operating at 5V.
With this relay you can easily control electrical appliances, lights, etc.
Features
-
- Opto-isolated input
- This relay module is 5V active low.
- It is an 1-channel relay interface board, which can be controlled directly by a wide range of microcontrollers.
- It is also able to control various appliances and other equipment with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Can be connected directly to microcontoller GPIO pins.
- Working status indicator lights are conducive to the safe use.
Qucik View -
Reviews
There are no reviews yet.