Only logged in customers who have purchased this product may leave a review.
I2C LCD Module + 20×4 LCD
₦ 10,250
Display more with the 20X4 LCD and conserve I/O pins with this kit. Alone, the LCD can take up as much as 12 I/O pins from your microcontroller. This kit combines the LCD with an I2C converter to ease connectivity and free up those valuable I/O pins. With I2C, only 2 I/O pins are used.
Features
- Arduino compatible I2C LCD module
- Software controlled backlight
- 20 X 4 LCD displays standard ASCII characters as well as special characters
- Widely available libraries for Arduino and other microcontroller architectures
- Example code at blog.nerdshed.com.ng
Kit Contains
- 20 X 4 LCD
- I2C converter
Related Products
-
5V DC 2 Channel Solid State Relay Module
₦ 3,000This is a 5V solid state relay 240V 2A, able to control sizable loads.
Features
-
- High current relay, AC250V 10A, DC30V 10A
- 2 LEDs to indicate when relays are on
- Works with logic level signals from 3.3V or 5V devices
- Opto-isolation circuitry
- PCB size: 50×45 mm
Qucik View -
-
4′ Raspberry Pi Screen (B, B+ & 2B)
₦ 51,300Qucik View -
Plastic Vernier Height & Depth Gauge Caliper- 0-150mm
₦ 8,500Product Description:
This product can measure the outer diameter, inner diameter, height, depth, etc.
Features:
Electronic digital caliper Made of hardened stainless steel Internal
external and height dimensions can be easily and accurately measured Linear capacitance measurement system Zero setting at any position Lock the jaws with a small locking thumb screw Basic measurement
Functions:
external, depth and step measurements.
easy-to-read LCD display Ideal for a wide range of industrial and automotive applications.
Qucik View -
Graphic LCD 84×48 – Nokia 5110 – Arduino Compatible
₦ 6,000The Nokia 5110 is a basic graphic LCD screen for lots of applications. A much richer information set can be displayed on this screen.
It uses the PCD8544 controller, same used in the Nokia 3310 LCD. The PCD8544 is a low power CMOS LCD controller/driver, designed to drive a graphic display of 48 rows and 84 columns. All necessary functions for the display are provided in a single chip, including on-chip generation of LCD supply and bias voltages, resulting in a minimum of external components and low power consumption. The PCD8544 interfaces to microcontrollers through a serial bus interface.
There is an Arduino library and MikroC library
Qucik View -
128 X 64 Graphic LCD Display
₦ 5,500This 128 x 64 Graphic LCD Module allows you to easily display graphics and text on screen. The NT7108 controller is very popular and widely supported.
- Built-in controller (NT7108 or equivalent)
- +5V power supply
- 1/64 duty cycle
- Built-in negative voltage
- Compatible with KS0108B and KS0107B controller
Pinout
1 V Power supply for logic 2 V Ground 3 V Contrast Adjustment 4~11 DB0~DB7 Data bus line 12 CS1 Select Column 1~ Column 64 13 CS2 Select Column 65~ Column 128 14 /RST Controller reset signal, Active Low 15 R/W Read/Write select signal 16 D/I Data/ Instruction select signal 17 E Enable signal 18 V Negative Voltage Output 19 A Power supply for B/L + 20 K Power supply for B/L Qucik View -
Dual USB Voltage And Current Tester
₦ 8,250This simple device can be used to operate or test servo motors. There are 3 modes to check servos;
- Manual mode: turn the knob
- Neutral mode: make the servo go back to the neutral point
- Automatic: window wiper mode: make the servo swing like a window wiper in the biggest angle. Push button to change between modes. Lights indicate mode.
You can connect 1-3 servos simultaneously. It can also be used to check the operation of any servo motor whether fitted or not.
Qucik View
Reviews
There are no reviews yet.