This tiny logic level shifter features four bidirectional channels, allowing for safe and easy communication between devices operating at different logic levels. It can convert signals as low as 1.5 V to as high as 18 V and vice versa, and its four channels are enough to support most common bidirectional and unidirectional digital interfaces, including I²C, SPI, and asynchronous TTL serial.
Bi-Directional 4 Channel Logic Level Converter
₦ 1,500
This tiny logic level shifter features four bidirectional channels, allowing for safe and easy communication between devices operating at different logic levels. It can convert signals as low as 1.5 V to as high as 18 V and vice versa, and its four channels are enough to support most common bidirectional and unidirectional digital interfaces, including I²C, SPI, and asynchronous TTL serial.
Only logged in customers who have purchased this product may leave a review.
Related Products
-
USB to RS-485 Converter
₦ 2,000The USB-RS-485 Converter allows you to interface and debug RS-485 devices from any terminal application or terminal application.
Features:
- No need external power, USB powered
- USB 2.0 plug and play compliant
- USB CH340 chip
- Support System: Windows XP , Vista, Windows 7 , Linux , MacOS , and WinCE5.0 support
- Supports baud rate range : 75bps – 115200bps , up to 6Mbps
- Communication distance :1200m(max)
Qucik View -
USB to UART 5- Pin CP2102 Module Serial Converter
₦ 2,500A MUST HAVE FOR EVERY ELECTRONICS AND EMBEDDED SYSTEMS ENGINEER
TALK DIRECTLY TO MICROCONTROLLERS, GSM MODULE, GPS MODULES, BLUETOOTH AND MANY MORE VIA UART/RS232
This is a USB 2.0 to 3.3V TTL UART 5 Pin CP 2102 Module Serial Converter
Connect MCU easily to your computer
Stable and reliable chip set CP2102 USB specifications
2.0 compliant with full-speed 12Mbps
Standard USB type A male and TTL 5 Pin connector
5 pins for TXD RXD GND 3.3V 5V.
All handshaking and modem interface signals.
Baud rate: 300bps to 1.5 Mbps.
Byte receive buffer: 640 byte transmit buffer.
Hardware or X-On/X-Off handshaking support.
Event character support Line break transmission.
USB suspend states supported via SUSPEND pins.
Temperature Range : -40 to + 85
Supports windows 98, Vista, Mac OS 9, Mac OS X & Linux 2.40
Qucik View -
AT-09-BLE-Bluetooth-4-0-Module—HM-10-Compatible-6620015
₦ 5,000This Bluetooth 4.0 TTL transceiver module allows you to communicate with any gadget using the highly energy efficient Bluetooth 4.0 specification
Features
- Power input: 3.6V-6V DC(Can not higher than 6V)
- It’s easy to use and safely enclosed in a plastic sheath
- Bluetooth version: V4.0
- Default baud rate: 9600 (Adjustable baudrate)
- Default serial port setting: 9600, N, 8, 1
- Operates as slave or master.
- Ultra-low standby power consumption 90uA~400uA
- Coverage up to 60 meters
- Built in PCB antenna
- Size: 43mm x 15mm
Pinout- VCC: input power supply 3.3~6V, Prohibit more than 7V
- GND: Ground
- TX: transport
- RX: receive
- State: when bluetooth is connected , output “High level”, “no conntected” output “low level”
- en:when module is connected, give a high level to “EN”,the module will disconnected.
Qucik View -
4 Channels Wireless Remote Control 315MHz -Arduino Compatible
₦ 4,000Communicate with Arduino over long distances
- 315MHz operating frequency
- Distance: approx. 50 Meters in open air
- 5V operation
- 4 Control channels
Qucik View -
LM2596 Adjustable Step-Down Power Module With Digital Display
₦ 3,500This board carries the multipurpose LM2596 power supply and allows you deliver a regulated voltage for any electronic device without the need for soldering or a multimeter. Simply set it and hook it up. The module displays the output voltage on a built in seven segment display.
Features
- 4V-40V Input Voltage.
- Continuously adjustable output voltage range of 1.25V-37V .
- Maximum output current up to 3A
- Switch toggles between viewing output or input voltage.
- Clear Seven Segment display for showing operating voltages
Qucik View -
I2C LCD Converter Module
₦ 1,500Description:-
I2C Module has a inbuilt PCF8574 I2C chip that converts I2C serial data to parallel data for the LCD display.
These modules are currently supplied with a default I2C address of either 0x27 or 0x3F. To determine which version you have check the black I2C adaptor board on the underside of the module. If there a 3 sets of pads labelled A0, A1, & A2 then the default address will be 0x3F. If there are no pads the default address will be 0x27.
The module has a contrast adjustment pot on the underside of the display. This may require adjusting for the screen to display text correctly.
Features:-
- Operating Voltage: 5V
- Backlight and Contrast is adjusted by potentiometer
- Serial I2C control of LCD display using PCF8574
- Come with 2 IIC interface, which can be connected by Dupont Line or IIC dedicated cable
- Compatible for 16×2 LCD
- This is another great IIC/I2C/TWI/SPI Serial Interface
- With this I2C interface module, you will be able to realize data display via only 2 wires.
Qucik View
Reviews
There are no reviews yet.