Only logged in customers who have purchased this product may leave a review.
Arduino Pro Mini and Programmer
₦ 9,000
Arduino Pro Mini is one of the smallest Arduinos out there. It comes with a decent microcontroller in a small package. In this kit, we have added a USB programmer kit to remove the headache of programming the Pro Mini.
Features
- Arduino IDE Compatible USB to UART Converter for programming
- ATmega328 running at 16MHz (5V)
- Bootloader already installed
- Max 150mA output
- Over current protected
- DC input 5V up to 12V (Via Vin)
- On board Power and Status LEDs
- Analog Pins: 8
- Digital I/Os: 14
Related Products
-
20 X 4 LCD Module – Arduino Compatible
₦ 5,000This 20 X 4 LCD Module allows you to fit in a lot more text than you can on the smaller 16X4. It is however fully compatible. It has the industry standard HD44780 LCD controller.
-
- 20X4 Characters
- 5V Operating voltage
- Fully pin and code compatible with 16X2, 16X1 LCDs
- Backlight
Qucik View -
-
MQ-2 Combustible Gas Sensor – Arduino Compatible
₦ 3,000This sensor allows you to detect combustible gases in the air. It is capable of detecting flamable gases in concentrations ranging from 300 to 10,000 ppm using only one analog pin from a microcontroller.
5V Operation
Detects any of the following flammable gases- LPG
- Butane
- Propane
- Methane
- Alcohol
- Hydrogen
- Smoke
Example Application: Fire prevention system, Gas leakage detector, Gas concentration detector.
Qucik View -
Micro SD Storage Board – Arduino Compatible
₦ 1,500This Micro SD card Adapter easibly adds Gigabytes of storage to your microcontroller project. Read and write from SD & SDHC cards via a microcontroller or Arduino board.
- Support Micro SD SDHC Card
- Power supply:4.5V – 5.5V, 3.3V voltage regulator circuit board
- Positioning holes: 4 M2 screws for mounting
- Control Interface: GND, VCC, MISO, MOSI, SCK, CS
Qucik View -
PN532 NFC and RFID Reader & Writer Module
₦ 6,000The PN532 is a widely used and supported NFC chip. This module will allow you to add NFC and RFID functionality to your project, allowing you to interact with phones, read and write NFC tags and RFID tags.
Features
- Typical Operating Distance have been updated to 5cm~7cm reading distance
- Work in NFC Mode or RFID reader/writer Mode
- RFID reader/writer supports:
- Mifare 1k, 4k, Ultralight, and DesFire cards
- ISO/IEC 14443-4 cards such as CD97BX, CD light, Desfire, P5CN072 (SMX)
- Innovision Jewel cards such as IRT5001 card
- FeliCa cards such as RCS_860 and RCS_854
- Plug and play, Arduino compatible
- Built in PCB Antenna, with 4cm~6cm communication distance
- On-board level shifter, Standard 5V TTL for I2C and UART, 3.3V TTL SPI
- Work as RFID reader/writer
- Work as 1443-A card or a virtual card
- Exchange data with other NFC devices such as smartphone
Package contains
- 1 PN532 NFC RFID Module
- 1 dupont cable Male-Male
- 1 Mifare S50 White Card
- 1 Mifare One S50 Key Ring
- 1 12P bent header pin
Arduino Library: //github.com/adafruit/Adafruit-PN532
Qucik View -
MQ-5 Methane, LPG, Alcohol & Smoke Sensor – Arduino Compatible
₦ 2,500This sensor allows you to detect combustible gases in the air. It is capable of detecting flamable gases in concentrations ranging from 200-10000ppm using only one analog pin from a microcontroller.
- 5V Operation
- Detects any of the following flammable gases
- Highly sensitive to LPG and Natural Gas
- Sensitive to Alcohol
- Cooking and Cigarette Smoke
Example Application: Fire prevention system, Gas leakage detector, Gas concentration detector.
Qucik View -
MQ-8 Hydrogen Gas Sensor – Arduino Compatible
₦ 3,000The MQ-8 hydrogen gas sensor, allows hydrogen gas concentrations to be measured. It has a sensitivity of 100-10000ppm. The Output is simply connected to an ADC via a load resistor
- 5V Operation
- Easy connection
- Highly sensitive
Qucik View
Reviews
There are no reviews yet.