Only logged in customers who have purchased this product may leave a review.
Arduino Buzzer Module
₦ 1,500
This module allows you to produce a rich and loud sound from your microcontroller.
- 3.3 V to 5 V Operating Voltage
- 3V to 5V Control
- Works without the need of a separate transistor
- Mounting Hole
Pin Out
-
- VCC (3.3 V to 5 V)
- GND
- I/O Control
Related Products
-
MQ-135 Air Quality/Pollution Sensor – Arduino Compatible
₦ 3,500The MQ-135 air quality and pollution sensor detects hazardous gases such as benzene, alcohol, smoke, CO2, NH3 and NOx(Nitrous Oxides) in the air. Analog out put can be interfaced directly to ADC of a microcontroller.
- 5V Operation.
- High sensitivity and response time.
Sample Applications: This sensor can be used to build air quality sensing devices for indoor and outdoor applications)
Qucik View -
MQ-8 Hydrogen Gas Sensor – Arduino Compatible
₦ 3,500The MQ-8 hydrogen gas sensor, allows hydrogen gas concentrations to be measured. It has a sensitivity of 100-10000ppm. The Output is simply connected to an ADC via a load resistor
- 5V Operation
- Easy connection
- Highly sensitive
Qucik View -
L298 H-Bridge Motor Driver – Arduino Compatible
₦ 4,000Basic attributes
Module name :Dual H-bridge motor driver module
Operating mode :H-bridge driver (dual)
Master chip :L298NLogic voltage :5V
Drive voltage :5V-35V
Logic Current :0mA-36mA
Drive current :2A (MAX single bridge)
Storage Temperature :-20 to 135Maximum Power :25W
Weight :30gExternal dimensions :43 * 43 * 27mmQucik View -
SCT-013 Non-invasive 100A Current Transformer (CT) -Arduino Compatible
₦ 11,750This current transformer allows you to easily measure to current running through a wire without tampering with the setup, simply pass the wire through or open up and clip around the wire.
Can be used for any of the following applications: Measurment and protection circuits, AC motors, lighting, air compressors, remote monitoring, Energy meters,etc
Features:
- Measures up to 100A
- Core material: ferrite
- Non-linearity 3%(10%-120% rated input current)
- 1.5m leading wire, with 3.5mmplug standard output.
- Two form of output current, voltage (voltage output built-in the burden resistor).
- Opening size:13mmx13mm
- Safety indicators: Dielectric strength 6000V AC/1min
- Meet UL94-V0 flame retardant properties
- Operating Temperature: -25 C ~ +70 C
Qucik View -
Graphic LCD 84×48 – Nokia 5110 – Arduino Compatible
₦ 6,000The Nokia 5110 is a basic graphic LCD screen for lots of applications. A much richer information set can be displayed on this screen.
It uses the PCD8544 controller, same used in the Nokia 3310 LCD. The PCD8544 is a low power CMOS LCD controller/driver, designed to drive a graphic display of 48 rows and 84 columns. All necessary functions for the display are provided in a single chip, including on-chip generation of LCD supply and bias voltages, resulting in a minimum of external components and low power consumption. The PCD8544 interfaces to microcontrollers through a serial bus interface.
There is an Arduino library and MikroC library
Qucik View -
DS18B20 Waterproof Temperature Sensor – Arduino Compatible
₦ 2,000The DS18B20 allows you take temperature readings in water or oils within its specified temperature range.
DS18B20 Technical specs:
- Usable temperature range: -55 to 125°C (-67°F to +257°F)
- 9 to 12 bit selectable resolution
- Uses 1-Wire interface- requires only one digital pin for communication
- Unique 64 bit ID burned into chip
- Multiple sensors can share one pin
- ±0.5°C Accuracy from -10°C to +85°C
- Temperature-limit alarm system
- Query time is less than 750ms
- Usable with 3.0V to 5.5V power/data
Work with Arduino IDE on ESP8266 Wifi module to take temperature readings over the Internet: //iot-playground.com/blog/2-uncategorised/41-esp8266-ds18b20-temperature-sensor-arduino-ide
Qucik View
Reviews
There are no reviews yet.