Only logged in customers who have purchased this product may leave a review.
A4988 Stepper Motor Driver Module

A4988 Stepper Motor Driver Module
₦ 2,000
A4988 is a microstepping stepper motor driver. It drives bipolar stepper motors and has adjustable current limit, over-current and over-temperature protection.
Key Featues:
-
- 8V to 32V Operating voltage
- 3-5V logic supply
- Up to 2A output current per coil
- 5 step resolutions: Full step, 1/2 step, 1/4 step, 1/8 step, 1/16 step
- Adjustable maximum current output
15 in stock
Related Products
-
0 out of 5
3V to 5V USB Output Step Up Power Module
₦ 1,000This module is excellent for charging mobile phones or powering other kinds of devices from 3V power sources such as Lithium Ion batteries or AA batteries. It delivers a regulated 5V output from a 3V input source.
Features:
- Input voltage: 1-5V
- Output voltage: 5.1-5 .2 V
- Output Current: Rated 1A-1.5A (single lithium input), the maximum 1.5A (single lithium input)
- Efficiency: Up to 96% (the higher the input voltage, the higher the efficiency)
- Switching frequency: 500KHz
- Input Reverse Polarity Protection: None
- Connection: Welding
- Input: IN + Postive, IN-Negative
- Output: USB Output
Can be used to easily make mobile power supply to charge and power MP3, Mobile phones or power bank from as little as a single cell.
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
A6 GSM & GPRS Module
₦ 8,500A module that supports dual-band GSM/GPRS network, available for GPRS and SMS. Comes ready to keep your project connected via phone calls, SMS, or the Internet.
- Working frequency: quad-band network, 850 / 900 / 1800 / 1900MHz
- Working voltage: 4.5~5.5V DC (On-board voltage regulator circuit supply power for A6 module)
- Working current: maximum of 2A
- Sleep current: 5mA
- Onboard Micro SIM card holder, you can install Micro SIM card
- Onboard Micro USB interface for external power supply
- Communication Interface: TTL serial port
- Baud rate: 115200bps and it can also be set by AT command.
- Interface logic voltage: 3.3V
- Make and answer phone calls using a headset and electret microphone.
- Send and receive SMS messages.
- Send and receive GPRS data (TCP/IP, HTTP, etc.)
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
HC-05 Master-Slave Bluetooth Module
₦ 3,000This module can be set as a transmitter or receiver, transmitter can pair with receiver , receiver and receiver or transmitter and transmitter can’t communication between eachother, receiver can pair with computers and cell phone’s bluetooth.
1. It is HC-05.
2. Uses the CSR mainstream bluetooth chip, bluetooth V2.0 protocol standards.
3. Module working voltage 3.3 V.
4. Potter default rate of 9600, the user can be set up.
5. The core module size : 28 mm x 15 mm x 2.35 mm.
6. Working current: matching for 30 MA, matching the communication for 8 MA.
7. Dormancy current: no dormancy.
8. Used for GPS navigation system, water and electricity gas meter reading system.
9. With computer and bluetooth bluetooth adapter, PDA, seamless connection equipmentCommercial Series: Bluetooth module board Series
With LED indicator light, use 150mA and 3.3V regulation chip.
With VCC.GND.TXD.RXD foot for the Bluetooth
With “Re-seach” button(ON/OFF/WAKE foot for it , external MCU outinput “High level” can control module to re-seach)
Compatible with bluetooth master module”.slave module”or master-slave(whole) module.
Input voltage: 3.3~6V
Size: 1.55cm*3.98cm
Note:input power supply 3.3~6V, Prohibit more than 7V
No “Automatically prevent power supply peversing func”, so please correctly connect power supply
We advise to install “Bluetooth master module”
The “State” is output foot for LED status, when bluetooth “Unconnected”, output “Pulse” ; when bluetooth “connected”, output “High level”, we can determine the states from “MCU”
If only the board , No any “Bluetooth Function “Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Ethernet Module – ENC28J60
₦ 4,000This module allows you to add Ethernet connectivity to your projects. Based on the popular Microchip’s ENC28J60, this module will easily interface with any Microcontroller or Arduino board allowing Internet Connectivity via the Ethernet..
- Up to 10Mbps
- 5V Tolerant I/O pins
- Fully IEEE 803.2 Standards compatible
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
20 X 4 LCD Module – Arduino Compatible
₦ 4,000This 20 X 4 LCD Module allows you to fit in a lot more text than you can on the smaller 16X4. It is however fully compatible. It has the industry standard HD44780 LCD controller.
-
- 20X4 Characters
- 5V Operating voltage
- Fully pin and code compatible with 16X2, 16X1 LCDs
- Backlight
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
-
0 out of 5
Arduino Dual-axis XY Joystick Module
₦ 2,000A joystick module which can be interfaced with a microcontroller like Arduino. It can be used in your robotics projects
-
- Dual-axis XY Joystick Module for Arduino
- Size: 4 X 2.6 X 3.2CM
- 2 potentiometers for 2 axes
- 1 switch
- Working voltage: 5V
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
Reviews
There are no reviews yet.