Only logged in customers who have purchased this product may leave a review.
XL4015 5A DC-DC Step Down Adjustable Supply Module with Display

XL4015 5A DC-DC Step Down Adjustable Supply Module with Display
₦ 3,500
The XL4015 power supply delivers up to 5A to loads that need more current. The output voltage and current are fully adjustable. This module comes complete with heat sink and mounting screws.
Features
- Input voltage range: 5-36VDC
- Output voltage range:1.25-32VDC adjustable
- Output current: 0-5A
- Output power: 75W
- High efficiency up to 96%
- Built in thermal shutdown function
- Built in current limit function
- Built in output short protection function
- Input reverse polarity protection: None (if required, high current diode in series with the input).
4 in stock
Related Products
-
0 out of 5
A6 GSM & GPRS Module
₦ 13,000A module that supports dual-band GSM/GPRS network, available for GPRS and SMS. Comes ready to keep your project connected via phone calls, SMS, or the Internet.
- Working frequency: quad-band network, 850 / 900 / 1800 / 1900MHz
- Working voltage: 4.5~5.5V DC (On-board voltage regulator circuit supply power for A6 module)
- Working current: maximum of 2A
- Sleep current: 5mA
- Onboard Micro SIM card holder, you can install Micro SIM card
- Onboard Micro USB interface for external power supply
- Communication Interface: TTL serial port
- Baud rate: 115200bps and it can also be set by AT command.
- Interface logic voltage: 3.3V
- Make and answer phone calls using a headset and electret microphone.
- Send and receive SMS messages.
- Send and receive GPRS data (TCP/IP, HTTP, etc.)
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Arduino Double Channel Relay Module 5V/10A
₦ 2,000This product is a 2-channel relay module board with LED indicators, It can be controlled by microcontrollers such as Arduino, AVR, PIC, ARM any other microcontroller operating at 5V.
With this relay you can easily control electrical appliances, lights, etc.
Features
-
- Opto-isolated input
- This relay module is 5V active low.
- It is an 1-channel relay interface board, which can be controlled directly by a wide range of microcontrollers.
- It is also able to control various appliances and other equipment with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Can be connected directly to microcontoller GPIO pins.
- Working status indicator lights are conducive to the safe use.
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
-
0 out of 5
5V DC 2 Channel Solid State Relay Module
₦ 3,000This is a 5V solid state relay 240V 2A, able to control sizable loads.
Features
-
- High current relay, AC250V 10A, DC30V 10A
- 2 LEDs to indicate when relays are on
- Works with logic level signals from 3.3V or 5V devices
- Opto-isolation circuitry
- PCB size: 50×45 mm
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
-
0 out of 5
12V Relay Module- 30A
₦ 800These Single Pole Double Throw(SPDT) relays are capable of switching up to 30A loads.
Features
-
- Single Pole Double Throw orientation
- 12V Coil
- Max Load (30A @ 220V AC and 30A @ 28V DC)
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
-
0 out of 5
3V to 5V USB Output Step Up Power Module
₦ 1,000This module is excellent for charging mobile phones or powering other kinds of devices from 3V power sources such as Lithium Ion batteries or AA batteries. It delivers a regulated 5V output from a 3V input source.
Features:
- Input voltage: 1-5V
- Output voltage: 5.1-5 .2 V
- Output Current: Rated 1A-1.5A (single lithium input), the maximum 1.5A (single lithium input)
- Efficiency: Up to 96% (the higher the input voltage, the higher the efficiency)
- Switching frequency: 500KHz
- Input Reverse Polarity Protection: None
- Connection: Welding
- Input: IN + Postive, IN-Negative
- Output: USB Output
Can be used to easily make mobile power supply to charge and power MP3, Mobile phones or power bank from as little as a single cell.
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Graphic LCD 84×48 – Nokia 5110 – Arduino Compatible
₦ 5,000The Nokia 5110 is a basic graphic LCD screen for lots of applications. A much richer information set can be displayed on this screen.
It uses the PCD8544 controller, same used in the Nokia 3310 LCD. The PCD8544 is a low power CMOS LCD controller/driver, designed to drive a graphic display of 48 rows and 84 columns. All necessary functions for the display are provided in a single chip, including on-chip generation of LCD supply and bias voltages, resulting in a minimum of external components and low power consumption. The PCD8544 interfaces to microcontrollers through a serial bus interface.
There is an Arduino library and MikroC library
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View
Reviews
There are no reviews yet.