Only logged in customers who have purchased this product may leave a review.
5 Red LEDs + 5 Resistors

5 Red LEDs + 5 Resistors
₦ 600
5 Red LED with 5 330 Ohm resistors. With these, all that needs to be done is connect to Microcontroller or Arduino GPIO pins. Works fine for 5V or 3V circuits
Out of stock
Related Products
-
0 out of 5
47 Ohm 1/4 Watt Resistor
₦ 40- Resistance: 47Ω
- Tolerance: 5%.
- Power rating:1/4Watt.
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
40 Wire Ribbon Cable -40Pins
₦ 1,500These ribbon cables are most useful in connecting LCDs, Modules or other boards. Each cable has crimped 40 cables connected to a housing.
Ribbon cables greatly simplify the task of connecting things up by eliminating the need for soldering.
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Stepper Motor – Nema 17 + A4988 Driver
₦ 12,000This stepper motor is perfect for robotics, 3D printer and other kinds of high precision projects. 1.8° per step smooth motion. The included A4988 motor driver allows you to safely, quickly and accurately working with the motor.
- 200 steps/rev
- 12V Operating Voltage
- 350mA (Max Current)
- 1.8 degrees per step
- Bipolar stepper motor
- 20 N*cm, 2 Kg*cm holding torque per phase
- 35 ohms per winding
- 42mm X 42mm square body -M3 Mounting Screws
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
MB-102 Breadboard
₦ 1,500This MB-102 Breadboard allows you to quickly prototype your projects in minutes
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
IR2110 + Free Socket
₦ 1,200The IR2110 is a high voltage, high speed power MOSFET and IGBT driver with independent high and low side referenced output channels. It is compatible with standard CMOS or LSTTL output, down to 3.3V logic.The floating channel can be used to drive an N-channel power MOSFET or IGBT in the high side configuration which operates up to 500 or 600 Volts.
It can be used to in inverter, solar and other power based projects to control MOSFET transistors or IGBT devices.
Features
- Floating channel designed for bootstrap operation Fully operational to +500V or +600V
- Gate drive supply range from 10 to 20V
- Undervoltage lockout for both channels
- 3.3V logic compatible Separate logic supply range from 3.3V to 20V Logic and power ground ±5V offset
- CMOS Schmitt-triggered inputs with pull-down
- Cycle by cycle edge-triggered shutdown logic
- Matched propagation delay for both channels
- Outputs in phase with inputs
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
5V 30A Single Channel Relay
₦ 2,200This product is a 1-channel relay module board with LED indicators, It can be controlled by microcontrollers such as Arduino, AVR, PIC, ARM any other microcontroller operating at 5V.
With this relay you can easily control electrical appliances, lights, etc.
Features:
- 5V Operation
- The static current:5mA
- Working current:190mA
- Trigger current:2-4mA
Module interface specifications:
-
- DC+ : DC power supply positive pole
- DC- :DC power supply negative pole
- IN : signal triggering pin
- JD+ : relay control voltage positive
- JD- : relay control voltage negative
- It is an 1-channel relay interface board, which can be controlled directly by a wide range of microcontrollers.
- It is also able to control various appliances and other equipment with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Can be connected directly to microcontoller GPIO pins.
- Working status indicator lights are conducive to the safe use.
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View
Reviews
There are no reviews yet.