Only logged in customers who have purchased this product may leave a review.
ESP8266-01 WiFi Module
ESP8266-01 WiFi Module
₦ 4,000
The ESP8266 WiFi Module allows you to add Internet conncetivity to your next electronic project. It has a built-in TCP/IP protocol stack. AT commands are issued over UART. Fully Arduino friendly.
- 3.3V Operating Voltage
- 802.11 b/g/n
- Wi-Fi Direct (P2P), soft-AP
- Integrated TCP/IP protocol stack
- Integrated low power 32-bit CPU could be used as application processor
- SDIO 1.1 / 2.0, SPI, UART
- Arduino compatible library
AT Command Set
//cdn.sparkfun.com/datasheets/Wireless/WiFi/Command%20Doc.pdf
Available on backorder
Related Products
-
0 out of 5
HB100 Motion Detection Microwave Sensor Module
₦ 3,500This is a X-Band Bi-Static Doppler transceiver module. This module can be used to detect motion in projects relating to home automation, automatic doors, alarm systems and even vehicle speed detection.
Feature
Transmission frequency: 10.525 GHz
Frequency Setting Accuracy: 3MHz
Output power (minimum): 13dBm EIRP
Operating voltage: 5V 0.25V
Operating Current (CW): 60mA max., 37mA typical
harmonic emission: <-10dBm
Pulse mode:
Averagecurrent (5% DC): 2mA
Pulse Width (Min.): 5uSec
load cycles (Min.): 1%Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
12V Relay Module – 10A –Pair
₦ 1,500This 6V Relay allows your to control loads with up to 10A consumption
Features:
-
- 6V Coil
- Maximum Load DC: 24V (DC) @ 10A
- Maximum Load AC: 240V (AC) @ 10A
- Maximum turn-on time: 10ms
- Maximum turn-off time: 5ms
- Easy through hole mounting arrangement
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
-
0 out of 5
3V to 5V USB Output Charger Step up Power Module
₦ 2,000This module is used as a DC-DC booster, converting 3V to 5V. With the aid of this board, you can charge your mobile phones and power other kinds of USB devices from power sources with voltage as little as 1.5V such as batteries.
- Non-isolated step-up module (BOOST)
- Input voltage: 1-5V
- Output voltage: 5.1-5 .2 V
- Output Current: Rated 1A-1.5A
- Efficiency: Up to 96% (the higher the input voltage, the higher the efficiency)
- Switching frequency: 500KHz
- Output ripple: 30mV (MAX) 20M bandwidth (input 4V output 5.1V 1A)
- Voltage indication: LED lights with load (input voltage less than 2.7V LED indicator off)
- Operating Temperature: Industrial (-40°c to +85°c)
- Full load temperature rise: 30°c
- Quiescent Current: 130uA
- Load regulation: ± 1%
- Voltage regulation: ± 0.5%
- Dynamic response speed: 5% 200uS
- Short circuit protection: None (Please use the lithium battery with protection.)
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Arduino Single Channel Relay Module 5V/10A
₦ 1,500This product is a 1-channel relay module board with LED indicators, It can be controlled by microcontrollers such as Arduino, AVR, PIC, ARM any other microcontroller operating at 5V.
With this relay you can easily control electrical appliances, lights, etc.
Features
-
- Diode protected input
- This relay module is 5V active low.
- It is an 1-channel relay interface board, which can be controlled directly by a wide range of microcontrollers.
- It is also able to control various appliances and other equipment with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Can be connected directly to microcontoller GPIO pins.
- Working status indicator lights are conducive to the safe use.
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
-
0 out of 5
LM2596 Adjustable Step-Down Power Module With Digital Display
₦ 3,500This board carries the multipurpose LM2596 power supply and allows you deliver a regulated voltage for any electronic device without the need for soldering or a multimeter. Simply set it and hook it up. The module displays the output voltage on a built in seven segment display.
Features
- 4V-40V Input Voltage.
- Continuously adjustable output voltage range of 1.25V-37V .
- Maximum output current up to 3A
- Switch toggles between viewing output or input voltage.
- Clear Seven Segment display for showing operating voltages
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Ethernet Module – ENC28J60
₦ 10,000This module allows you to add Ethernet connectivity to your projects. Based on the popular Microchip’s ENC28J60, this module will easily interface with any Microcontroller or Arduino board allowing Internet Connectivity via the Ethernet..
- Up to 10Mbps
- 5V Tolerant I/O pins
- Fully IEEE 803.2 Standards compatible
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View
Reviews
There are no reviews yet.