Only logged in customers who have purchased this product may leave a review.
12V Relay Module- 30A

12V Relay Module- 30A
₦ 800
These Single Pole Double Throw(SPDT) relays are capable of switching up to 30A loads.
Features
-
- Single Pole Double Throw orientation
- 12V Coil
- Max Load (30A @ 220V AC and 30A @ 28V DC)
Out of stock
Related Products
-
0 out of 5
5A XL4015 DC-DC Step down Adjustable Power Supply Module
₦ 1,800This buck DC step-down adjustable power supply module allows you to power projects and deliver up to 5A current at 1.25V to 36V
- Input voltage range:4V to 38V
- Output voltage range:1.25-36V adjustable
- Output current: 0-5A
- Output power: 75W
- High efficiency up to 96%
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
CP2102 MICRO USB to UART TTL Module
₦ 1,5005A constant current LED driver and charger for lithium-ion battery
· 3.3V and 5V voltage output
· Supports baud rates from 300bps ~ 1Mbps
On-chip voltage regulator output voltage 3.3V
Supports data formats for 8 data bits, 1 stop bit and parity bits
Connotation 512 byte receive buffer and 512 byte transmit buffer
Support for hardware or X-ON / X-OFF handshakeProduct added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
A4988 Stepper Motor Driver Module
₦ 2,000A4988 is a microstepping stepper motor driver. It drives bipolar stepper motors and has adjustable current limit, over-current and over-temperature protection.
Key Featues:
-
- 8V to 32V Operating voltage
- 3-5V logic supply
- Up to 2A output current per coil
- 5 step resolutions: Full step, 1/2 step, 1/4 step, 1/8 step, 1/16 step
- Adjustable maximum current output
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
-
0 out of 5
Arduino Dual-axis XY Joystick Module
₦ 1,500A joystick module which can be interfaced with a microcontroller like Arduino. It can be used in your robotics projects
-
- Dual-axis XY Joystick Module for Arduino
- Size: 4 X 2.6 X 3.2CM
- 2 potentiometers for 2 axes
- 1 switch
- Working voltage: 5V
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
-
0 out of 5
Ethernet Module – ENC28J60
₦ 5,000This module allows you to add Ethernet connectivity to your projects. Based on the popular Microchip’s ENC28J60, this module will easily interface with any Microcontroller or Arduino board allowing Internet Connectivity via the Ethernet..
- Up to 10Mbps
- 5V Tolerant I/O pins
- Fully IEEE 803.2 Standards compatible
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
HC-05 Master-Slave Bluetooth Module
₦ 5,500This module can be set as a transmitter or receiver, transmitter can pair with receiver , receiver and receiver or transmitter and transmitter can’t communication between eachother, receiver can pair with computers and cell phone’s bluetooth.
1. It is HC-05.
2. Uses the CSR mainstream bluetooth chip, bluetooth V2.0 protocol standards.
3. Module working voltage 3.3 V.
4. Potter default rate of 9600, the user can be set up.
5. The core module size : 28 mm x 15 mm x 2.35 mm.
6. Working current: matching for 30 MA, matching the communication for 8 MA.
7. Dormancy current: no dormancy.
8. Used for GPS navigation system, water and electricity gas meter reading system.
9. With computer and bluetooth bluetooth adapter, PDA, seamless connection equipmentCommercial Series: Bluetooth module board Series
With LED indicator light, use 150mA and 3.3V regulation chip.
With VCC.GND.TXD.RXD foot for the Bluetooth
With “Re-seach” button(ON/OFF/WAKE foot for it , external MCU outinput “High level” can control module to re-seach)
Compatible with bluetooth master module”.slave module”or master-slave(whole) module.
Input voltage: 3.3~6V
Size: 1.55cm*3.98cm
Note:input power supply 3.3~6V, Prohibit more than 7V
No “Automatically prevent power supply peversing func”, so please correctly connect power supply
We advise to install “Bluetooth master module”
The “State” is output foot for LED status, when bluetooth “Unconnected”, output “Pulse” ; when bluetooth “connected”, output “High level”, we can determine the states from “MCU”
If only the board , No any “Bluetooth Function “Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View
Reviews
There are no reviews yet.