Only logged in customers who have purchased this product may leave a review.
16×2 LCD Module

16×2 LCD Module
₦ 3,000
16X2 LCD Module with Blue backlight
-
- Easily controlled from any microcontroller
- 4/8 bit communication mode
- Special character mode
- Blue backlight
- HD44780 Controller
Related Products
-
0 out of 5
20 X 4 LCD Module – Arduino Compatible
₦ 5,000This 20 X 4 LCD Module allows you to fit in a lot more text than you can on the smaller 16X4. It is however fully compatible. It has the industry standard HD44780 LCD controller.
-
- 20X4 Characters
- 5V Operating voltage
- Fully pin and code compatible with 16X2, 16X1 LCDs
- Backlight
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
-
0 out of 5
Dual USB Power Bank Board with LCD Display
₦ 2,500Dual USB battery charger with a built in LCD module for visual feedback
Features
-
- Micro USB input: 5V 1A
- USB Output: 5V 2.1A / 5V 1A(Dual USB interface)
- Charging display: LCD
- Batteries Type: Lithium-ion batteries (18650)
- Product Size: 57mm x 28mm
- Screen size:27mm x 17mm
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
-
0 out of 5
I2C LCD Converter Module
₦ 1,500Description:-
I2C Module has a inbuilt PCF8574 I2C chip that converts I2C serial data to parallel data for the LCD display.
These modules are currently supplied with a default I2C address of either 0x27 or 0x3F. To determine which version you have check the black I2C adaptor board on the underside of the module. If there a 3 sets of pads labelled A0, A1, & A2 then the default address will be 0x3F. If there are no pads the default address will be 0x27.
The module has a contrast adjustment pot on the underside of the display. This may require adjusting for the screen to display text correctly.
Features:-
- Operating Voltage: 5V
- Backlight and Contrast is adjusted by potentiometer
- Serial I2C control of LCD display using PCF8574
- Come with 2 IIC interface, which can be connected by Dupont Line or IIC dedicated cable
- Compatible for 16×2 LCD
- This is another great IIC/I2C/TWI/SPI Serial Interface
- With this I2C interface module, you will be able to realize data display via only 2 wires.
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Graphic LCD 84×48 – Nokia 5110 – Arduino Compatible
₦ 5,000The Nokia 5110 is a basic graphic LCD screen for lots of applications. A much richer information set can be displayed on this screen.
It uses the PCD8544 controller, same used in the Nokia 3310 LCD. The PCD8544 is a low power CMOS LCD controller/driver, designed to drive a graphic display of 48 rows and 84 columns. All necessary functions for the display are provided in a single chip, including on-chip generation of LCD supply and bias voltages, resulting in a minimum of external components and low power consumption. The PCD8544 interfaces to microcontrollers through a serial bus interface.
There is an Arduino library and MikroC library
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
128 X 64 Graphic LCD Display
₦ 5,500This 128 x 64 Graphic LCD Module allows you to easily display graphics and text on screen. The NT7108 controller is very popular and widely supported.
- Built-in controller (NT7108 or equivalent)
- +5V power supply
- 1/64 duty cycle
- Built-in negative voltage
- Compatible with KS0108B and KS0107B controller
Pinout
1 V Power supply for logic 2 V Ground 3 V Contrast Adjustment 4~11 DB0~DB7 Data bus line 12 CS1 Select Column 1~ Column 64 13 CS2 Select Column 65~ Column 128 14 /RST Controller reset signal, Active Low 15 R/W Read/Write select signal 16 D/I Data/ Instruction select signal 17 E Enable signal 18 V Negative Voltage Output 19 A Power supply for B/L + 20 K Power supply for B/L Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Ethernet Module – ENC28J60
₦ 5,000This module allows you to add Ethernet connectivity to your projects. Based on the popular Microchip’s ENC28J60, this module will easily interface with any Microcontroller or Arduino board allowing Internet Connectivity via the Ethernet..
- Up to 10Mbps
- 5V Tolerant I/O pins
- Fully IEEE 803.2 Standards compatible
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View
Reviews
There are no reviews yet.