Only logged in customers who have purchased this product may leave a review.
Micro USB to DIP Adapter- Pair
Micro USB to DIP Adapter- Pair
₦ 1,500
These Micro USB to DIP converter boards allow easy connection of a microcontroller or arduino to a PC using standard USB interface.
It may also be used to power a device over the USB port
- 3cm x 3cm x 3cm
Related Products
-
0 out of 5
IR2110 + Free Socket
₦ 1,200The IR2110 is a high voltage, high speed power MOSFET and IGBT driver with independent high and low side referenced output channels. It is compatible with standard CMOS or LSTTL output, down to 3.3V logic.The floating channel can be used to drive an N-channel power MOSFET or IGBT in the high side configuration which operates up to 500 or 600 Volts.
It can be used to in inverter, solar and other power based projects to control MOSFET transistors or IGBT devices.
Features
- Floating channel designed for bootstrap operation Fully operational to +500V or +600V
- Gate drive supply range from 10 to 20V
- Undervoltage lockout for both channels
- 3.3V logic compatible Separate logic supply range from 3.3V to 20V Logic and power ground ±5V offset
- CMOS Schmitt-triggered inputs with pull-down
- Cycle by cycle edge-triggered shutdown logic
- Matched propagation delay for both channels
- Outputs in phase with inputs
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Resistor Value Pack – 22 Values
₦ 2,000This 22 Value resistor pack contains most of the resistors you will need 10 pieces each of resistors ranging from 10Ω to 10MΩ
- 10Ω
- 22Ω
- 47Ω
- 100Ω
- 220Ω
- 330Ω
- 470Ω
- 680Ω
- 1kΩ
- 2.2kΩ
- 4.7kΩ
- 6.8kΩ
- 10kΩ
- 22kΩ
- 47kΩ
- 68kΩ
- 100kΩ
- 220kΩ
- 470kΩ
- 680kΩ
- 1MΩ
- 10MΩ
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
MAX232 + Free Socket and Capacitors
₦ 1,000The MAX232 is an integrated circuit which converts signals from a TIA-232 (RS-232) serial port to signals suitable for use in TTL-compatible digital logic circuits such as microcontrollers. The MAX232 is a dual transmitter / dual receiver that typically is used to convert the RX, TX, CTS, RTS signals.
MAX232.
Features
- Meets or Exceeds TIA/EIA-232-F and ITU Recommendation V.28
- Operates From a Single 5-V Power Supply With 1.0-F Charge-Pump Capacitors
- Operates Up To 120 kbit/s
- Two Drivers and Two Receivers sot that up to two devices can use the same chip or flow control lines such as DTR and CTS.
- ±30-V Input Levels
- Low Supply Current… 8 mA Typical
- ESD Protection
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
R2323 to TTL Converter with Dupont Cable
₦ 1,500This module suitable for any 3.3v or 5v microcontroller and Arduino
• Fully compatible with existing legacy COM port software
• Output signals: VDD, TXD, RXD, CTS, RTS, GND
• Power, TX, RX LED
• Power input: 3.3V or 5VPackage List:
1 * RS232 Serial To TTL Converter Module
4 * Dupont Jumping CableProduct added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
5V 30A Single Channel Relay
₦ 2,500This product is a 1-channel relay module board with LED indicators, It can be controlled by microcontrollers such as Arduino, AVR, PIC, ARM any other microcontroller operating at 5V.
With this relay you can easily control electrical appliances, lights, etc.
Features:
- 5V Operation
- The static current:5mA
- Working current:190mA
- Trigger current:2-4mA
Module interface specifications:
-
- DC+ : DC power supply positive pole
- DC- :DC power supply negative pole
- IN : signal triggering pin
- JD+ : relay control voltage positive
- JD- : relay control voltage negative
- It is an 1-channel relay interface board, which can be controlled directly by a wide range of microcontrollers.
- It is also able to control various appliances and other equipment with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Can be connected directly to microcontoller GPIO pins.
- Working status indicator lights are conducive to the safe use.
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
L298 H-Bridge Motor Driver – Arduino Compatible
₦ 4,000Basic attributes
Module name :Dual H-bridge motor driver module
Operating mode :H-bridge driver (dual)
Master chip :L298NLogic voltage :5V
Drive voltage :5V-35V
Logic Current :0mA-36mA
Drive current :2A (MAX single bridge)
Storage Temperature :-20 to 135Maximum Power :25W
Weight :30gExternal dimensions :43 * 43 * 27mmProduct added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View
Reviews
There are no reviews yet.