Only logged in customers who have purchased this product may leave a review.
DHT11 TEMPERATURE SENSOR
DHT11 TEMPERATURE SENSOR
₦ 2,500
The DHT11 is a low-cost and reliable digital temperature and humidity sensor. Digital output only. It is compatible with Arduino complete with library as well as other microcontrollers.
- 3 to 5V Operating range
- 2.5mA (max)
- 20-80% humidity readings (up to 5% accuracy)
- 0-50°C temperature readings (up to ±2°C accuracy)
- 1 Hz Maximum sampling rate
- 15.5mm x 12mm x 5.5mm
- 4 pins with 0.1″ spacing
Pins
1. VCC
2. Data
3. NC
4. Ground
Related Products
-
0 out of 5
W1219 Thermostat Temperature Controller Switch Module + Waterproof NTC Sensor Module
₦ 6,500A digital temperature controller module with dual LED display and an inbuilt relay module for control. The cut-off temperature is set with buttons on board
- Control Range:-50~110 Celsius
- Control Precision:0.1 Celsius
- Measuring Input: NTC10K waterproof sensor L=0.5m
- High Temperature Alarm:-49~110 Celsius
- Input Voltage: DC 12V
- Output Type: relay output 10A (max)
- Return Difference Setting:0.1~30 degree Celsius
- Delay Starting:0-10min
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
MQ-7 Carbon Monoxide Sensor – Arduino Compatible
₦ 4,000The MQ-7 Carbon Monoxide (CO) gas sensor, allows Carbon monoxide concentrations to be measured. It has a sensitivity of 20ppm-2000ppm. The Output is simply connected to an ADC via a load resistor
- 5V Operation
- Safely measure poisonous CO concentrations
- Highly sensitive CO
- Easy connection
- Highly sensitive
Applications: CO alarm, anti carbon monoxide poisoning system.
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Pulse Sensor -Arduino Compatible
₦ 6,000This pulse sensor measure heart rate by simly being in contact with a finger or earlobe.
- 3-5V Operation
- Pulse Sensor Board
- Coded Cable with Standard Male Headers
For a tutorials and sample code, visit: //pulsesensor.com/pages/code-and-guide
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
MQ-5 Methane, LPG, Alcohol & Smoke Sensor – Arduino Compatible
₦ 3,500This sensor allows you to detect combustible gases in the air. It is capable of detecting flamable gases in concentrations ranging from 200-10000ppm using only one analog pin from a microcontroller.
- 5V Operation
- Detects any of the following flammable gases
- Highly sensitive to LPG and Natural Gas
- Sensitive to Alcohol
- Cooking and Cigarette Smoke
Example Application: Fire prevention system, Gas leakage detector, Gas concentration detector.
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
DHT22 Temperature and Humidity Sensor
₦ 10,500DHT-22 is a humidity and temperature sensor with read out over single wire digital interface. The sensor is already calibrated and doesn’t need extra components so you can measure relative humidity and temperature right away.
- 3 to 5V power and I/O
- 2.5mA max current use during conversion (while requesting data)
- Good for 0-100% humidity readings with 2-5% accuracy
- Good for -40 to 80°C temperature readings ±0.5°C accuracy
- No more than 0.5 Hz sampling rate (once every 2 seconds)
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
MQ-135 Air Quality/Pollution Sensor – Arduino Compatible
₦ 3,500The MQ-135 air quality and pollution sensor detects hazardous gases such as benzene, alcohol, smoke, CO2, NH3 and NOx(Nitrous Oxides) in the air. Analog out put can be interfaced directly to ADC of a microcontroller.
- 5V Operation.
- High sensitivity and response time.
Sample Applications: This sensor can be used to build air quality sensing devices for indoor and outdoor applications)
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View
Reviews
There are no reviews yet.