Only logged in customers who have purchased this product may leave a review.
Water Flow Sensor

Water Flow Sensor
₦ 4,500
Measure the flow rate of water. This can be used in control system projects that require the rate of water flow to be measured and controlled.
- working voltage: DC4.5 5V-24V
- maximum operating current: 15 mA (DC 5V)
- working voltage range: DC 5~18 v
- load capacity: 10 mA (DC 5V)
- use temperature: 80
- operating humidity range: 35%~90%RH (no frost)
- allowing pressure: pressure 1.75Mpa
- temperature: -25~+80 ° c
Related Products
-
0 out of 5
MC-38 Wired Door & Window Sensor Module
₦ 1,000This door/window sensor modules are useful in detecting the state of doors, windows, drawers or cupboards. It can be easily interfaced directly to a microcontroller or an Arduino.
- Normally open reed switch
- Easily installed on doors, windows and drawers with screws
- Rated current: 100 mA max
- Rated voltage: 100VDC max
- 15mm maximum operating space.
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Thermocouple Temperature Sensor Module MAX31855K
₦ 2,800The MAX31855 is cold junction compensation, K, J, N, T or E type thermocouple signal into a digital value. The device outputs data 14 signed by SPITM compatible interface, in read-only format. Converter temperature resolution of 0.25 ?, the highest temperature reading of +1800 ?, the lowest temperature reading of -270 ?, the K-type thermocouple, a temperature range of -200 ? to + 700 ?, maintaining accuracy ±2 ?.
Can the device be used in a temperature regulated and sensing projects and applications to detect temperatures up to 1,800?
3.3 to 5V power supply and logic level compliant
SPI data output requires any 3 digital I/O pins.
-200°C to +1350°C output in 0.25-degree increments – note that K thermocouples have about ±2°C to ±6°C accuracy
Internal temperature reading.Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Infra-Red Flame Sensor
₦ 1,000This module is sensitive to the flame and radiation. It also can detect ordinary light source in the range of of a wavelength 760nm-1100 nm. It can be used as a flame alarm or in fire fighting robots.
Features
Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm.
Detection range: up to 100 cm.
Adjustable detection range.
Detection angle about 60 degrees, it is sensitive to the flame spectrum.
Comparator chip LM393 makes module readings stable.
Operating voltage 3.3V-5V.
Digital and Analog Output.
Power indicator and digital switch output indicator.
Interface Description (4-wire)VCC — 3.3V-5V voltage
GND — GND
DO — Digital output interface (0 or 1)
AO — Analog output interfaceProduct added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
DHT22 Temperature and Humidity Sensor
₦ 4,000DHT-22 is a humidity and temperature sensor with read out over single wire digital interface. The sensor is already calibrated and doesn’t need extra components so you can measure relative humidity and temperature right away.
- 3 to 5V power and I/O
- 2.5mA max current use during conversion (while requesting data)
- Good for 0-100% humidity readings with 2-5% accuracy
- Good for -40 to 80°C temperature readings ±0.5°C accuracy
- No more than 0.5 Hz sampling rate (once every 2 seconds)
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
DS18B20 Waterproof Temperature Sensor – Arduino Compatible
₦ 2,000The DS18B20 allows you take temperature readings in water or oils within its specified temperature range.
DS18B20 Technical specs:
- Usable temperature range: -55 to 125°C (-67°F to +257°F)
- 9 to 12 bit selectable resolution
- Uses 1-Wire interface- requires only one digital pin for communication
- Unique 64 bit ID burned into chip
- Multiple sensors can share one pin
- ±0.5°C Accuracy from -10°C to +85°C
- Temperature-limit alarm system
- Query time is less than 750ms
- Usable with 3.0V to 5.5V power/data
Work with Arduino IDE on ESP8266 Wifi module to take temperature readings over the Internet: //iot-playground.com/blog/2-uncategorised/41-esp8266-ds18b20-temperature-sensor-arduino-ide
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
MQ-8 Hydrogen Gas Sensor – Arduino Compatible
₦ 3,000The MQ-8 hydrogen gas sensor, allows hydrogen gas concentrations to be measured. It has a sensitivity of 100-10000ppm. The Output is simply connected to an ADC via a load resistor
- 5V Operation
- Easy connection
- Highly sensitive
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View
Reviews
There are no reviews yet.