Only logged in customers who have purchased this product may leave a review.
STM8S103F3P6 Mini Dev Board
₦ 1,500
This STM8S103 Minimum development board is suitable for STM8 enthusiast. It packs a lot of power in a very small package.
- 16 MHz advanced STM8 core with Harvard architecture and 3-stage pipeline
- RAM: 1 Kbyte
- 2.95 to 5.5 V operating voltage
- Internal, user-trimmable 16 MHz RC
- Internal low-power 128 kHz RC
- On-board 5V Regulator.
- Can be powered by 5V USB port
- Support SWIM programming.
- 2 Built-In LEDs Power and GPIO on pin PD3 (This should flash when you power it up)
- On board reset button
- 8K Flash Memory
- 640 bytes EEPROM
- Reflash up to 10K times
6 in stock
Related Products
-
3V to 5V USB Output Step Up Power Module
₦ 1,000This module is excellent for charging mobile phones or powering other kinds of devices from 3V power sources such as Lithium Ion batteries or AA batteries. It delivers a regulated 5V output from a 3V input source.
Features:
- Input voltage: 1-5V
- Output voltage: 5.1-5 .2 V
- Output Current: Rated 1A-1.5A (single lithium input), the maximum 1.5A (single lithium input)
- Efficiency: Up to 96% (the higher the input voltage, the higher the efficiency)
- Switching frequency: 500KHz
- Input Reverse Polarity Protection: None
- Connection: Welding
- Input: IN + Postive, IN-Negative
- Output: USB Output
Can be used to easily make mobile power supply to charge and power MP3, Mobile phones or power bank from as little as a single cell.
Qucik View -
Arduino AT-TINY85 Digispark Board
₦ 2,000The AT-Tiny85 Board is perfect for developing projects where an Arduino would be “too much”. It allows you to perform basic I/O and computing functions and is fully compatible with the Arduino IDE.
Features
- Fully supported on Arduino IDE
- Can be powered via USB or External Source – 5V or 7-35V (12V or less recommended)
- On-board 500ma 5V Regulator
- I2C and SPI (via USI)
- PWM on 3 pins (more possible with Software PWM)
- ADC on 4 pins
- Power LED and Test/Status LED
Product InformationBrandQucik View -
MP3 Decoder Board With Remote Control
₦ 3,500A highly integrated single-chip multimedia sound systems allows you to play MP3 files from a flash disk or SD card. It is also an FM player and can accept auxilliary input from a 3.5mm jack.
FEATURES
- Single decoding, Support the MP3 format music.
- Digital tube display
- Support the TF card.have the USB interface.
- Support FM radio, cable band (87.5MHZ-108.0MHZ);
- Support 5-10 meter distance infrared remote control operation
- Support for external audio input .LINE IN(AUX)
- key-press: VOL-/ AUTO / VOL+ / MODE;
- MODE key: in turn switches between USB/SD/FM/AUX.
Qucik View -
Mini Digital LCD Indoor Thermometer and Hygrometer
₦ 2,000This mini digital thermometer and hygrometer displays ambient temperature and relative humidity
- Modern type indoor desk thermometer with hygrometer.
- Indoor temperature °C(min. or max.) and humidity (max. or min.) display.
- Clear and correct display with easy to read arabic numerals
- It is widely used for the measurement of the temperature and humidity in houses, offices, workshops, schools, markets, warehouses, etc
- Indoor temperature range: 0°C~50°C.
- Up to 0.1°C accuracy.
- Humidity range: 20%RH~95%RH.
- Powered by two button batteries. (Included)
Qucik View -
ARM STM32F103C8T6 Development Board
₦ 11,000This board is low cost ARM Microcontroller development board – STM32F103C8T6. The board is suitable for learners and professionals alike who want the 32-bit power of ARM Coretex-M3 32-bit core.
Code for it can be written using MirkroC ARM, Keil MDK, Eclipse GCC, and many more.
Easily load code into the chip via UART (check out our USB-UART converter) //www.konga.com/usb-to-uart-5-pin-cp2102-module-serial-converter-1988801
You DON’T need a programmer, flash using //cdn2.starkled.com/content/uploads/2012/11/Flash_Loader_Demonstrator_v2.5.0_Setup.exe
Features
- On-board Mini USB interface, you can give the board power supply and USB communication.
- On-board test indicator LED
- On-board reset button and power indicator LED
- On-board 100ma 3.3V Regulator
- All GPIO are led out and the names of the pins are marked
- After soldering the headers, you can directly plug the board onto the breadboard
Technical Specifications
- CPU Part Number: STM32F103C8T6
- Core: ARM 32 Cortex-M3 CPU.
- Debug mode: SWD (can be programmed with ST-LINK V2)
- CPU Internal Maximum Clock : 72MHz
- External Clock Source: 8MHz crystal
- 64K flash memory, 20K SRAM
- 2.0-3.6V power, I/O
Programming Instructions
- Set Boot Jumper-0 to 1
- Set Boot Jumper-1 to 0
- Connect USB-TTL Converter’s TX to PA10 on STM Board
- Connect USB-TTL Converter’s RX to PA9 on STM Board
- Give 3.3V power to STM board using USB TTL converter
- Press and release reset button once
- Launch STM Flash Loader, Select Port Name (where your usb ttl converter is connected)
- Select Parity as Even, Baudate as 115200, Echo Disabled and Timeout 10s
- Press Next, and follow on screen instructions to program, erase or read STM microcontroller
Qucik View -
Mini Submersible Water Pump
₦ 2,000This simple DC submersible pump allows you to pump water at a rate of up to 120L/H and operates at 3-5V
Features
- DC Voltage: 3-6V
- Maximum lift:40-110cm / 15.75″-43.4″
- Flow rate:80-120L/H
- Outside diameter of water outlet: 7.5mm / 0.3″
- Inside diameter of water outlet: 4.7mm / 0.18″
- Diameter:Approx. 24mm / 0.95″
- Length:Approx. 45mm / 1.8″
- Height:Approx. 33mm / 1.30″
- Plastic
- Driving mode: Brushless DC Motor
- Continuous working life of 500 hours
Qucik View
Reviews
There are no reviews yet.