Only logged in customers who have purchased this product may leave a review.
Single Sided A4 Copper Clad PCB Board
- You cannot add "PCB Drill kit" to the cart because the product is out of stock.
Single Sided A4 Copper Clad PCB Board
₦ 1,500
These low cost Single-sided copper-clad printed circuit board made from paper-based material. They are very useful when making simple single sided prototype boards.
- Great for prototypes and short run PCB
- low-cost printed circuit board.
- Easy to drill and cut.
- Suitable etchant ferric chloride solution.
- 210 × 297mm
Related Products
-
0 out of 5
Arduino Single Channel Relay Module 5V/10A
₦ 1,500This product is a 1-channel relay module board with LED indicators, It can be controlled by microcontrollers such as Arduino, AVR, PIC, ARM any other microcontroller operating at 5V.
With this relay you can easily control electrical appliances, lights, etc.
Features
-
- Diode protected input
- This relay module is 5V active low.
- It is an 1-channel relay interface board, which can be controlled directly by a wide range of microcontrollers.
- It is also able to control various appliances and other equipment with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Can be connected directly to microcontoller GPIO pins.
- Working status indicator lights are conducive to the safe use.
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
-
0 out of 5
Printed Circuit Board Etch Resistant Marker Pen
₦ 1,000This two sided etch resist pen for fast fabrication of printed circuit boards. The ink adheres perfectly to copper and is completely resistant to ferric chloride and other usual etchant solutions. Draw the planned circuit onto a thoroughly cleaned copper laminated board and allow to dry. Then immerse the board in etching fluid until the copper is dissolved. The ink can then be removed with Degreasing Solvent or PCB Cleaner, and the circuit board is then ready to be drilled and assembled. This pen is capable of producing thin, delicate lines allowing for quite a condensed track layout if required.
It can also be used to correct broken tracks while making PCB using toner resist method
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
4 Channel 5V Relay Module
₦ 7,000This board is built specifically for the ESP8266 WiFi module. It allows you to control all kinds of devices over the Internet from the wildly popular ESP8266-01 Module. Simply power up and program the board.
- Board size: 45 * 28 mm
- Board function description:
- IN +, IN-: 5V power input;
- TX, RX, GND: Serial debug pin
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Channel Digital Amplifier Board with Subwoofer Output
₦ 6,500This stereo amplifier is allows you to easily deliver a powerful sound up to 200W! And all you need to do is connect a transformer.
FEATURES
- Output power:80W+80W
- Output Impedance:4-8 Ohms
- Frequency range:20Hz-30kHz
- Microphone input
- SNR:100dB
- Number of channels:3 (left channel,right channel,subwoofer)
- Product size: about 13.2*14.2*6.1cm/5.2* 5.6*2.4inch
- Power Supply: AC +/-24V (>120w) ring transformer (Please use a high power transformer or DC power supply for best output.
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Arduino AT-TINY85 Digispark Board
₦ 2,000The AT-Tiny85 Board is perfect for developing projects where an Arduino would be “too much”. It allows you to perform basic I/O and computing functions and is fully compatible with the Arduino IDE.
Features
- Fully supported on Arduino IDE
- Can be powered via USB or External Source – 5V or 7-35V (12V or less recommended)
- On-board 500ma 5V Regulator
- I2C and SPI (via USI)
- PWM on 3 pins (more possible with Software PWM)
- ADC on 4 pins
- Power LED and Test/Status LED
Product InformationBrandProduct added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
ESP8266-01 Relay Board
₦ 7,750This board is built specifically for the ESP8266 WiFi module. It allows you to control all kinds of devices over the Internet from the wildly popular ESP8266-01 Module. Simply power up and program the board.
- Board size: 45 * 28 mm
- Board function description:
- IN +, IN-: 5V power input;
- TX, RX, GND: Serial debug pin
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View
Reviews
There are no reviews yet.