Only logged in customers who have purchased this product may leave a review.
SCT-013 Non-invasive 100A Current Transformer (CT) -Arduino Compatible
SCT-013 Non-invasive 100A Current Transformer (CT) -Arduino Compatible
₦ 11,750
This current transformer allows you to easily measure to current running through a wire without tampering with the setup, simply pass the wire through or open up and clip around the wire.
Can be used for any of the following applications: Measurment and protection circuits, AC motors, lighting, air compressors, remote monitoring, Energy meters,etc
Features:
- Measures up to 100A
- Core material: ferrite
- Non-linearity 3%(10%-120% rated input current)
- 1.5m leading wire, with 3.5mmplug standard output.
- Two form of output current, voltage (voltage output built-in the burden resistor).
- Opening size:13mmx13mm
- Safety indicators: Dielectric strength 6000V AC/1min
- Meet UL94-V0 flame retardant properties
- Operating Temperature: -25 C ~ +70 C
Related Products
-
0 out of 5
Arduino Double Channel Relay Module 5V/10A
₦ 3,500This product is a 2-channel relay module board with LED indicators, It can be controlled by microcontrollers such as Arduino, AVR, PIC, ARM any other microcontroller operating at 5V.
With this relay you can easily control electrical appliances, lights, etc.
Features
-
- Opto-isolated input
- This relay module is 5V active low.
- It is an 1-channel relay interface board, which can be controlled directly by a wide range of microcontrollers.
- It is also able to control various appliances and other equipment with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Can be connected directly to microcontoller GPIO pins.
- Working status indicator lights are conducive to the safe use.
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
-
0 out of 5
Graphic LCD 84×48 – Nokia 5110 – Arduino Compatible
₦ 6,000The Nokia 5110 is a basic graphic LCD screen for lots of applications. A much richer information set can be displayed on this screen.
It uses the PCD8544 controller, same used in the Nokia 3310 LCD. The PCD8544 is a low power CMOS LCD controller/driver, designed to drive a graphic display of 48 rows and 84 columns. All necessary functions for the display are provided in a single chip, including on-chip generation of LCD supply and bias voltages, resulting in a minimum of external components and low power consumption. The PCD8544 interfaces to microcontrollers through a serial bus interface.
There is an Arduino library and MikroC library
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
MQ-2 Combustible Gas Sensor – Arduino Compatible
₦ 4,000This sensor allows you to detect combustible gases in the air. It is capable of detecting flamable gases in concentrations ranging from 300 to 10,000 ppm using only one analog pin from a microcontroller.
5V Operation
Detects any of the following flammable gases- LPG
- Butane
- Propane
- Methane
- Alcohol
- Hydrogen
- Smoke
Example Application: Fire prevention system, Gas leakage detector, Gas concentration detector.
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Arduino Nano
₦ 9,750The Arduino Nano is a full featured breadboard-friendly Arduino board. It is based on an Atmega 328 microcontroller. Fully programmable with Arduino IDE
Key Features:
- 5V Operating Voltage
- 7-12 Volt Unregulated Supply Voltage
- 8 Analog Input Pins
- 14 Digital I/O Pins
- 32kB Flash Memory (2kB Bootloader)
- 1kB RAM
- 512 Bytes EEPROM
- UART
- SPI
- PWM
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Arduino Buzzer Module
₦ 1,500This module allows you to produce a rich and loud sound from your microcontroller.
- 3.3 V to 5 V Operating Voltage
- 3V to 5V Control
- Works without the need of a separate transistor
- Mounting Hole
Pin Out
-
- VCC (3.3 V to 5 V)
- GND
- I/O Control
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
Rated 5.00 out of 5
Arduino Uno
₦ 16,500The Arduino Uno R3 is a microcontroller board based on the ATmega328. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
The Uno differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip.
Additional features coming with the R3 version are:
ATmega16U2 instead 8U2 as USB-to-Serial converter.
1.0 pinout: added SDA and SCL pins for TWI communication placed near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board and the second one is a not connected pin, that is reserved for future purposes.
stronger RESET circuit.
“Uno” means “One” in Italian and is named to mark the upcoming release of Arduino 1.0. The Uno and version 1.0 will be the reference versions of Arduino, moving forward. The Uno is the latest in a series of USB Arduino boards, and the reference model for the Arduino platform.Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limit) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) PWM Digital I/O Pins 6 Analog Input Pins 6 DC Current per I/O Pin 20 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB of which 0.5 KB used by bootloader SRAM 2 KB EEPROM 1 KB Clock Speed 16 MHz LED_BUILTIN 13 Length 68.6 mm Width 53.4 mm Weight 25 g Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View
Reviews
There are no reviews yet.