Only logged in customers who have purchased this product may leave a review.
Pickit3 Microcontroller Programmer – Debugger

Pickit3 Microcontroller Programmer – Debugger
₦ 16,000
Pickit3 PIC microcontroller programmer and debugger. Included in the pack are
- PICkit3 programmer
- USB Cable
- ICSP Connector cable
This programmer can load code an debug all PIC12, PIC16, PIC18, PIC24, PIC32, DSPIC family of microcontrollers.
3 in stock
Related Products
-
0 out of 5
8-Bit Microcontroller – PIC18F452
₦ 3,500High-Performance 8 bit Microcontrollers.
Features inlude:
-
- Capable 40MHz operation (10 Million Instructions per Second)
- 32K Flash Memory
- 1.5kB RAM
- 8X8 Hardware Multiplier
- UART Module
- 10bit ADC Module
- ICSP Programming
- PWM Module
- I2C Module
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
-
0 out of 5
ATMEGA 328P-PU
₦ 1,900This high-performance Atmel 8-bit AVR RISC-based microcontroller combines 32KB ISP flash memory
- Flash Memory 32 kBytes
- 1024B EEPROM
- 2KB SRAM
- Pin Count: 32
- Max. Operating Freq. (MHz): 20 MHz
- CPU: 8-bit AVR
- 23 GPIO pins
- 24 Interrupt Sources
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
High-Speed USB SPI Programmer – EZP2010
₦ 12,000This programmer can read and write the BIOS chips of a DVD,TV,etc
- USB 2.0 interface, the speed is 12Mbps.
- Auto detect chip modules.
- Auto select power voltage.
- Auto off-line chip copy.
- Software and firmware update.
- Support chip of 25 FLASH, 24 EEPROM, 25 EEPROM, 93 EEPROM, etc
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
ST-Link V2 STM8/STM32 Programmer & Emulator
₦ 7,000This pocket friendly USB programmer and debugger allows STM8 and STM32 (ARM) microcontrollers to be programmed and debugged.
Product Features:
- Support for all the STM8 devices via SWIM interface
- Support for all STM32 devices with SWD interface
- Debugging : run at full-speed, single-stepped, breakpoints, viewing variables and registers, etc.
- Programming : supports FLASH ROM, EEPROM, AFR, etc.
- Onboard 500mA self-recovery fuse to avoid harming by short circuit
- Dual voltage output (3.3V/5V), easy for debugging/programming
- Standard USB interface to PC
- USB2.0 combined with SWIM/SWD interfaces : quick response for debugging & fast speed for programming
- Upgradable firmware
The board supports any of the following softwares:
- ST – LINK Utility 2.0 and above
- STVD 2 and above
- STVP 3.2.3 and above
- IAR EWARM V6.20 and above
- IAR EWSTM8 V1.30 and above
- KEIL RVMDK V4.21 and above
- ATOLLIC
- TASKING
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Arduino LilyPad – Atmega 328 Model
₦ 6,000The LilyPad Arduino 328 Board is an Arduino based board designed for making wearable and e-textile type projects. It is fully Arduino compatible and has holes for easily sewing it into projects. LEDs, Sensors, buttons and so much more can be easily integrated.
Features:
- ATmega328 Microcontroller
- Operating Voltage 2.7-5.5 V
- Input Voltage 2.7-5.5 V
- Digital I/O Pins 14
- PWM Channels 6
- Analog Input Channels 6
- DC Current per I/O Pin 40 mA
- Flash Memory 16 KB (of which 2 KB used by bootloader)
- SRAM 1 KB
- EEPROM 512 bytes
- Clock Speed 8 MHz
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
ARM STM32F103C8T6 Development Board
₦ 3,500This board is low cost ARM Microcontroller development board – STM32F103C8T6. The board is suitable for learners and professionals alike who want the 32-bit power of ARM Coretex-M3 32-bit core.
Code for it can be written using MirkroC ARM, Keil MDK, Eclipse GCC, and many more.
Easily load code into the chip via UART (check out our USB-UART converter) //www.konga.com/usb-to-uart-5-pin-cp2102-module-serial-converter-1988801
You DON’T need a programmer, flash using //cdn2.starkled.com/content/uploads/2012/11/Flash_Loader_Demonstrator_v2.5.0_Setup.exe
Features
- On-board Mini USB interface, you can give the board power supply and USB communication.
- On-board test indicator LED
- On-board reset button and power indicator LED
- On-board 100ma 3.3V Regulator
- All GPIO are led out and the names of the pins are marked
- After soldering the headers, you can directly plug the board onto the breadboard
Technical Specifications
- CPU Part Number: STM32F103C8T6
- Core: ARM 32 Cortex-M3 CPU.
- Debug mode: SWD (can be programmed with ST-LINK V2)
- CPU Internal Maximum Clock : 72MHz
- External Clock Source: 8MHz crystal
- 64K flash memory, 20K SRAM
- 2.0-3.6V power, I/O
Programming Instructions
- Set Boot Jumper-0 to 1
- Set Boot Jumper-1 to 0
- Connect USB-TTL Converter’s TX to PA10 on STM Board
- Connect USB-TTL Converter’s RX to PA9 on STM Board
- Give 3.3V power to STM board using USB TTL converter
- Press and release reset button once
- Launch STM Flash Loader, Select Port Name (where your usb ttl converter is connected)
- Select Parity as Even, Baudate as 115200, Echo Disabled and Timeout 10s
- Press Next, and follow on screen instructions to program, erase or read STM microcontroller
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View
Reviews
There are no reviews yet.