Only logged in customers who have purchased this product may leave a review.
PIC16F628A Microcontroller
₦ 2,000
16F Family Midrange Microcontroller with 18 pins delivering up to 4MIPS
- 4MHz internal oscillator
- 2-5.5V Operation
- 1 UART
- PWM
- 224Byte RAM
- 128 Byte EEPROM
- Programmable via ICSP
Out of stock
Related Products
-
Raspberry Pi 4 (2GB RAM)
₦ 150,000Dual-display, desktop computer and robot brains, smart home hub, media center, networked AI core, factory controller, and much more
Qucik View -
Arduino LilyPad – Atmega 328 Model
₦ 6,000The LilyPad Arduino 328 Board is an Arduino based board designed for making wearable and e-textile type projects. It is fully Arduino compatible and has holes for easily sewing it into projects. LEDs, Sensors, buttons and so much more can be easily integrated.
Features:
- ATmega328 Microcontroller
- Operating Voltage 2.7-5.5 V
- Input Voltage 2.7-5.5 V
- Digital I/O Pins 14
- PWM Channels 6
- Analog Input Channels 6
- DC Current per I/O Pin 40 mA
- Flash Memory 16 KB (of which 2 KB used by bootloader)
- SRAM 1 KB
- EEPROM 512 bytes
- Clock Speed 8 MHz
Qucik View -
Raspberry Pi 4 (4GB RAM)
₦ 175,000Dual-display, desktop computer and robot brains, smart home hub, media center, networked AI core, factory controller, and much more
Qucik View -
PICkit 3 + Free Pic – 16F628
₦ 35,000PICkit 3 In-Circuit Debugger/Programmer uses in-circuit debugging logic incorporated into each chip with Flash memory to provide a low-cost hardware debugger and programmer. With the PICkit3, almost any Microchip PIC microcontroller can be programmed and debugged.
Free 16F628 8-bit microcontroller included.
Features
- USB (Full speed 12 Mbits/s interface to host PC)
- Real-time execution
- MPLAB IDE compatible (free copy included)
- Built-in over-voltage/short circuit monitor
- Firmware upgradeable from PC/web download
- Totally enclosed
- Supports low voltage to 2.0 volts (2.0v to 6.0V range)
- Diagnostic LEDs (power, busy, error)
- Read/write program and data memory of microcontroller
- Erase of program memory space with verification
- Freeze-peripherals at breakpoint
- Program up to 512K byte flash with the Programmer-to-Go
- Free 16F628 microcontroller included
Qucik View -
ARM STM32F103C8T6 Development Board
₦ 9,500This board is low cost ARM Microcontroller development board – STM32F103C8T6. The board is suitable for learners and professionals alike who want the 32-bit power of ARM Coretex-M3 32-bit core.
Code for it can be written using MirkroC ARM, Keil MDK, Eclipse GCC, and many more.
Easily load code into the chip via UART (check out our USB-UART converter) //www.konga.com/usb-to-uart-5-pin-cp2102-module-serial-converter-1988801
You DON’T need a programmer, flash using //cdn2.starkled.com/content/uploads/2012/11/Flash_Loader_Demonstrator_v2.5.0_Setup.exe
Features
- On-board Mini USB interface, you can give the board power supply and USB communication.
- On-board test indicator LED
- On-board reset button and power indicator LED
- On-board 100ma 3.3V Regulator
- All GPIO are led out and the names of the pins are marked
- After soldering the headers, you can directly plug the board onto the breadboard
Technical Specifications
- CPU Part Number: STM32F103C8T6
- Core: ARM 32 Cortex-M3 CPU.
- Debug mode: SWD (can be programmed with ST-LINK V2)
- CPU Internal Maximum Clock : 72MHz
- External Clock Source: 8MHz crystal
- 64K flash memory, 20K SRAM
- 2.0-3.6V power, I/O
Programming Instructions
- Set Boot Jumper-0 to 1
- Set Boot Jumper-1 to 0
- Connect USB-TTL Converter’s TX to PA10 on STM Board
- Connect USB-TTL Converter’s RX to PA9 on STM Board
- Give 3.3V power to STM board using USB TTL converter
- Press and release reset button once
- Launch STM Flash Loader, Select Port Name (where your usb ttl converter is connected)
- Select Parity as Even, Baudate as 115200, Echo Disabled and Timeout 10s
- Press Next, and follow on screen instructions to program, erase or read STM microcontroller
Qucik View -
Pickit3 Microcontroller Programmer – Debugger
₦ 30,000Pickit3 PIC microcontroller programmer and debugger. Included in the pack are
- PICkit3 programmer
- USB Cable
- ICSP Connector cable
This programmer can load code an debug all PIC12, PIC16, PIC18, PIC24, PIC32, DSPIC family of microcontrollers.
Qucik View
Reviews
There are no reviews yet.