Only logged in customers who have purchased this product may leave a review.
MQ-2 Combustible Gas Sensor – Arduino Compatible
MQ-2 Combustible Gas Sensor – Arduino Compatible
₦ 4,000
This sensor allows you to detect combustible gases in the air. It is capable of detecting flamable gases in concentrations ranging from 300 to 10,000 ppm using only one analog pin from a microcontroller.
5V Operation
Detects any of the following flammable gases
- LPG
- Butane
- Propane
- Methane
- Alcohol
- Hydrogen
- Smoke
Example Application: Fire prevention system, Gas leakage detector, Gas concentration detector.
Related Products
-
0 out of 5
MQ-135 Air Quality/Pollution Sensor – Arduino Compatible
₦ 3,500The MQ-135 air quality and pollution sensor detects hazardous gases such as benzene, alcohol, smoke, CO2, NH3 and NOx(Nitrous Oxides) in the air. Analog out put can be interfaced directly to ADC of a microcontroller.
- 5V Operation.
- High sensitivity and response time.
Sample Applications: This sensor can be used to build air quality sensing devices for indoor and outdoor applications)
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Micro SD Storage Board – Arduino Compatible
₦ 1,500This Micro SD card Adapter easibly adds Gigabytes of storage to your microcontroller project. Read and write from SD & SDHC cards via a microcontroller or Arduino board.
- Support Micro SD SDHC Card
- Power supply:4.5V – 5.5V, 3.3V voltage regulator circuit board
- Positioning holes: 4 M2 screws for mounting
- Control Interface: GND, VCC, MISO, MOSI, SCK, CS
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
MQ-7 Carbon Monoxide Sensor – Arduino Compatible
₦ 4,000The MQ-7 Carbon Monoxide (CO) gas sensor, allows Carbon monoxide concentrations to be measured. It has a sensitivity of 20ppm-2000ppm. The Output is simply connected to an ADC via a load resistor
- 5V Operation
- Safely measure poisonous CO concentrations
- Highly sensitive CO
- Easy connection
- Highly sensitive
Applications: CO alarm, anti carbon monoxide poisoning system.
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
L298 H-Bridge Motor Driver – Arduino Compatible
₦ 4,000Basic attributes
Module name :Dual H-bridge motor driver module
Operating mode :H-bridge driver (dual)
Master chip :L298NLogic voltage :5V
Drive voltage :5V-35V
Logic Current :0mA-36mA
Drive current :2A (MAX single bridge)
Storage Temperature :-20 to 135Maximum Power :25W
Weight :30gExternal dimensions :43 * 43 * 27mmProduct added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
PN532 NFC and RFID Reader & Writer Module
₦ 9,000The PN532 is a widely used and supported NFC chip. This module will allow you to add NFC and RFID functionality to your project, allowing you to interact with phones, read and write NFC tags and RFID tags.
Features
- Typical Operating Distance have been updated to 5cm~7cm reading distance
- Work in NFC Mode or RFID reader/writer Mode
- RFID reader/writer supports:
- Mifare 1k, 4k, Ultralight, and DesFire cards
- ISO/IEC 14443-4 cards such as CD97BX, CD light, Desfire, P5CN072 (SMX)
- Innovision Jewel cards such as IRT5001 card
- FeliCa cards such as RCS_860 and RCS_854
- Plug and play, Arduino compatible
- Built in PCB Antenna, with 4cm~6cm communication distance
- On-board level shifter, Standard 5V TTL for I2C and UART, 3.3V TTL SPI
- Work as RFID reader/writer
- Work as 1443-A card or a virtual card
- Exchange data with other NFC devices such as smartphone
Package contains
- 1 PN532 NFC RFID Module
- 1 dupont cable Male-Male
- 1 Mifare S50 White Card
- 1 Mifare One S50 Key Ring
- 1 12P bent header pin
Arduino Library: //github.com/adafruit/Adafruit-PN532
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Ethernet Module – ENC28J60
₦ 10,000This module allows you to add Ethernet connectivity to your projects. Based on the popular Microchip’s ENC28J60, this module will easily interface with any Microcontroller or Arduino board allowing Internet Connectivity via the Ethernet..
- Up to 10Mbps
- 5V Tolerant I/O pins
- Fully IEEE 803.2 Standards compatible
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View
Reviews
There are no reviews yet.