Only logged in customers who have purchased this product may leave a review.
MQ-2 Combustible Gas Sensor – Arduino Compatible
₦ 3,000
This sensor allows you to detect combustible gases in the air. It is capable of detecting flamable gases in concentrations ranging from 300 to 10,000 ppm using only one analog pin from a microcontroller.
5V Operation
Detects any of the following flammable gases
- LPG
- Butane
- Propane
- Methane
- Alcohol
- Hydrogen
- Smoke
Example Application: Fire prevention system, Gas leakage detector, Gas concentration detector.
Related Products
-
Arduino Mega
₦ 28,500The Arduino Mega is just the Arduino for when you need to bring the big guns out. It has 54 GPIO, 4 UART pins, 16 Analog inputs and more
Features
- Microcontroller ATmega2560
- Operating Voltage 5V
- Input Voltage (recommended) 7-12V
- Input Voltage (limits) 6-20V
- Digital I/O Pins 54 (of which 15 provide PWM output)
- Analog Input Pins 16
- DC Current per I/O Pin 40 mA
- DC Current for 3.3V Pin 50 mA
- Flash Memory 256 KB of which 8 KB used by bootloader
- SRAM 8 KB
- EEPROM 4 KB
- Clock Speed 16 MHz
- Resettable polyfuse that protects PC USB ports from shorts and overcurrent
Qucik View -
Arduino Buzzer Module
₦ 1,500This module allows you to produce a rich and loud sound from your microcontroller.
- 3.3 V to 5 V Operating Voltage
- 3V to 5V Control
- Works without the need of a separate transistor
- Mounting Hole
Pin Out
-
- VCC (3.3 V to 5 V)
- GND
- I/O Control
Qucik View -
MQ-7 Carbon Monoxide Sensor – Arduino Compatible
₦ 3,000The MQ-7 Carbon Monoxide (CO) gas sensor, allows Carbon monoxide concentrations to be measured. It has a sensitivity of 20ppm-2000ppm. The Output is simply connected to an ADC via a load resistor
- 5V Operation
- Safely measure poisonous CO concentrations
- Highly sensitive CO
- Easy connection
- Highly sensitive
Applications: CO alarm, anti carbon monoxide poisoning system.
Qucik View -
Pulse Sensor -Arduino Compatible
₦ 4,500This pulse sensor measure heart rate by simly being in contact with a finger or earlobe.
- 3-5V Operation
- Pulse Sensor Board
- Coded Cable with Standard Male Headers
For a tutorials and sample code, visit: //pulsesensor.com/pages/code-and-guide
Qucik View -
Arduino Nano
₦ 7,500The Arduino Nano is a full featured breadboard-friendly Arduino board. It is based on an Atmega 328 microcontroller. Fully programmable with Arduino IDE
Key Features:
- 5V Operating Voltage
- 7-12 Volt Unregulated Supply Voltage
- 8 Analog Input Pins
- 14 Digital I/O Pins
- 32kB Flash Memory (2kB Bootloader)
- 1kB RAM
- 512 Bytes EEPROM
- UART
- SPI
- PWM
Qucik View -
Graphic LCD 84×48 – Nokia 5110 – Arduino Compatible
₦ 5,000The Nokia 5110 is a basic graphic LCD screen for lots of applications. A much richer information set can be displayed on this screen.
It uses the PCD8544 controller, same used in the Nokia 3310 LCD. The PCD8544 is a low power CMOS LCD controller/driver, designed to drive a graphic display of 48 rows and 84 columns. All necessary functions for the display are provided in a single chip, including on-chip generation of LCD supply and bias voltages, resulting in a minimum of external components and low power consumption. The PCD8544 interfaces to microcontrollers through a serial bus interface.
There is an Arduino library and MikroC library
Qucik View
Reviews
There are no reviews yet.