Only logged in customers who have purchased this product may leave a review.
MP3 Decoder Board With Remote Control

MP3 Decoder Board With Remote Control
₦ 3,500
A highly integrated single-chip multimedia sound systems allows you to play MP3 files from a flash disk or SD card. It is also an FM player and can accept auxilliary input from a 3.5mm jack.
FEATURES
- Single decoding, Support the MP3 format music.
- Digital tube display
- Support the TF card.have the USB interface.
- Support FM radio, cable band (87.5MHZ-108.0MHZ);
- Support 5-10 meter distance infrared remote control operation
- Support for external audio input .LINE IN(AUX)
- key-press: VOL-/ AUTO / VOL+ / MODE;
- MODE key: in turn switches between USB/SD/FM/AUX.
Out of stock
Related Products
-
0 out of 5
20 X 4 LCD Module – Arduino Compatible
₦ 5,000This 20 X 4 LCD Module allows you to fit in a lot more text than you can on the smaller 16X4. It is however fully compatible. It has the industry standard HD44780 LCD controller.
-
- 20X4 Characters
- 5V Operating voltage
- Fully pin and code compatible with 16X2, 16X1 LCDs
- Backlight
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
-
0 out of 5
USB To ESP8266 Serial Wireless Wi-Fi Module Adapter Board
₦ 2,500This USB ESP8266 adapter board which can be plugged directly to your computer allowing communication, testing and programming to be done on the module with ease.
· CH340 serial chip
· 3225 chip crystal, to enhance the stability of the serial port
Fully compatible with Windows, Mac and Linux systems
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
A6 GSM & GPRS Module
₦ 13,000A module that supports dual-band GSM/GPRS network, available for GPRS and SMS. Comes ready to keep your project connected via phone calls, SMS, or the Internet.
- Working frequency: quad-band network, 850 / 900 / 1800 / 1900MHz
- Working voltage: 4.5~5.5V DC (On-board voltage regulator circuit supply power for A6 module)
- Working current: maximum of 2A
- Sleep current: 5mA
- Onboard Micro SIM card holder, you can install Micro SIM card
- Onboard Micro USB interface for external power supply
- Communication Interface: TTL serial port
- Baud rate: 115200bps and it can also be set by AT command.
- Interface logic voltage: 3.3V
- Make and answer phone calls using a headset and electret microphone.
- Send and receive SMS messages.
- Send and receive GPRS data (TCP/IP, HTTP, etc.)
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
ARM STM32F103C8T6 Development Board
₦ 11,000This board is low cost ARM Microcontroller development board – STM32F103C8T6. The board is suitable for learners and professionals alike who want the 32-bit power of ARM Coretex-M3 32-bit core.
Code for it can be written using MirkroC ARM, Keil MDK, Eclipse GCC, and many more.
Easily load code into the chip via UART (check out our USB-UART converter) //www.konga.com/usb-to-uart-5-pin-cp2102-module-serial-converter-1988801
You DON’T need a programmer, flash using //cdn2.starkled.com/content/uploads/2012/11/Flash_Loader_Demonstrator_v2.5.0_Setup.exe
Features
- On-board Mini USB interface, you can give the board power supply and USB communication.
- On-board test indicator LED
- On-board reset button and power indicator LED
- On-board 100ma 3.3V Regulator
- All GPIO are led out and the names of the pins are marked
- After soldering the headers, you can directly plug the board onto the breadboard
Technical Specifications
- CPU Part Number: STM32F103C8T6
- Core: ARM 32 Cortex-M3 CPU.
- Debug mode: SWD (can be programmed with ST-LINK V2)
- CPU Internal Maximum Clock : 72MHz
- External Clock Source: 8MHz crystal
- 64K flash memory, 20K SRAM
- 2.0-3.6V power, I/O
Programming Instructions
- Set Boot Jumper-0 to 1
- Set Boot Jumper-1 to 0
- Connect USB-TTL Converter’s TX to PA10 on STM Board
- Connect USB-TTL Converter’s RX to PA9 on STM Board
- Give 3.3V power to STM board using USB TTL converter
- Press and release reset button once
- Launch STM Flash Loader, Select Port Name (where your usb ttl converter is connected)
- Select Parity as Even, Baudate as 115200, Echo Disabled and Timeout 10s
- Press Next, and follow on screen instructions to program, erase or read STM microcontroller
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Printed Circuit Board Etch Resistant Marker Pen
₦ 1,000This two sided etch resist pen for fast fabrication of printed circuit boards. The ink adheres perfectly to copper and is completely resistant to ferric chloride and other usual etchant solutions. Draw the planned circuit onto a thoroughly cleaned copper laminated board and allow to dry. Then immerse the board in etching fluid until the copper is dissolved. The ink can then be removed with Degreasing Solvent or PCB Cleaner, and the circuit board is then ready to be drilled and assembled. This pen is capable of producing thin, delicate lines allowing for quite a condensed track layout if required.
It can also be used to correct broken tracks while making PCB using toner resist method
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
5A XL4015 DC-DC Step down Adjustable Power Supply Module
₦ 1,800This buck DC step-down adjustable power supply module allows you to power projects and deliver up to 5A current at 1.25V to 36V
- Input voltage range:4V to 38V
- Output voltage range:1.25-36V adjustable
- Output current: 0-5A
- Output power: 75W
- High efficiency up to 96%
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View
Reviews
There are no reviews yet.