Only logged in customers who have purchased this product may leave a review.
Mini Submersible Water Pump
₦ 2,500
This simple DC submersible pump allows you to pump water at a rate of up to 120L/H and operates at 3-5V
Features
- DC Voltage: 3-6V
- Maximum lift:40-110cm / 15.75″-43.4″
- Flow rate:80-120L/H
- Outside diameter of water outlet: 7.5mm / 0.3″
- Inside diameter of water outlet: 4.7mm / 0.18″
- Diameter:Approx. 24mm / 0.95″
- Length:Approx. 45mm / 1.8″
- Height:Approx. 33mm / 1.30″
- Plastic
- Driving mode: Brushless DC Motor
- Continuous working life of 500 hours
Related Products
-
R2323 to TTL Converter with Dupont Cable
₦ 1,500This module suitable for any 3.3v or 5v microcontroller and Arduino
• Fully compatible with existing legacy COM port software
• Output signals: VDD, TXD, RXD, CTS, RTS, GND
• Power, TX, RX LED
• Power input: 3.3V or 5VPackage List:
1 * RS232 Serial To TTL Converter Module
4 * Dupont Jumping CableQucik View -
L298 H-Bridge Motor Driver – Arduino Compatible
₦ 4,000Basic attributes
Module name :Dual H-bridge motor driver module
Operating mode :H-bridge driver (dual)
Master chip :L298NLogic voltage :5V
Drive voltage :5V-35V
Logic Current :0mA-36mA
Drive current :2A (MAX single bridge)
Storage Temperature :-20 to 135Maximum Power :25W
Weight :30gExternal dimensions :43 * 43 * 27mmQucik View -
IR2110 + Free Socket
₦ 1,200The IR2110 is a high voltage, high speed power MOSFET and IGBT driver with independent high and low side referenced output channels. It is compatible with standard CMOS or LSTTL output, down to 3.3V logic.The floating channel can be used to drive an N-channel power MOSFET or IGBT in the high side configuration which operates up to 500 or 600 Volts.
It can be used to in inverter, solar and other power based projects to control MOSFET transistors or IGBT devices.
Features
- Floating channel designed for bootstrap operation Fully operational to +500V or +600V
- Gate drive supply range from 10 to 20V
- Undervoltage lockout for both channels
- 3.3V logic compatible Separate logic supply range from 3.3V to 20V Logic and power ground ±5V offset
- CMOS Schmitt-triggered inputs with pull-down
- Cycle by cycle edge-triggered shutdown logic
- Matched propagation delay for both channels
- Outputs in phase with inputs
Qucik View -
NEMA 17 Motor and Coupling
₦ 14,000This stepper motor and coupling pair are perfect for robotics, 3D printer and other kinds of high precision projects. 1.8° per step smooth motion. It also has a solid holding torque.
- 5mm Shaft
- 5mm X 5mm Coupling
- 200 steps/rev
- 12V Operating Voltage
- 350mA (Max Current)
- 1.8 degrees per step
- Bipolar stepper motor
- 20 N*cm, 2 Kg*cm holding torque per phase
- 35 ohms per winding
- 42mm X 42mm square body -M3 Mounting Screws
Qucik View -
5V 30A Single Channel Relay
₦ 2,500This product is a 1-channel relay module board with LED indicators, It can be controlled by microcontrollers such as Arduino, AVR, PIC, ARM any other microcontroller operating at 5V.
With this relay you can easily control electrical appliances, lights, etc.
Features:
- 5V Operation
- The static current:5mA
- Working current:190mA
- Trigger current:2-4mA
Module interface specifications:
-
- DC+ : DC power supply positive pole
- DC- :DC power supply negative pole
- IN : signal triggering pin
- JD+ : relay control voltage positive
- JD- : relay control voltage negative
- It is an 1-channel relay interface board, which can be controlled directly by a wide range of microcontrollers.
- It is also able to control various appliances and other equipment with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Can be connected directly to microcontoller GPIO pins.
- Working status indicator lights are conducive to the safe use.
Qucik View -
Mini USB 5V USB to 3.3V DC Power Outlet
₦ 1,500This DC power outlet allows connectivity of power and data to electronic projects. It allows USB data pins (D+ and D-) to be connected to a USB capable microcontroller. It also carries a 3.3V regulator on board and allows 5V devices to be powered as well.
USB Input: 5V
DC power socket input: 5-12V
Output: 5V and 3.3V
Qucik View
Reviews
There are no reviews yet.