Only logged in customers who have purchased this product may leave a review.
MC-38 Wired Door & Window Sensor Module
₦ 2,000
This door/window sensor modules are useful in detecting the state of doors, windows, drawers or cupboards. It can be easily interfaced directly to a microcontroller or an Arduino.
- Normally open reed switch
- Easily installed on doors, windows and drawers with screws
- Rated current: 100 mA max
- Rated voltage: 100VDC max
- 15mm maximum operating space.
Related Products
-
DHT22 Temperature and Humidity Sensor
₦ 10,500DHT-22 is a humidity and temperature sensor with read out over single wire digital interface. The sensor is already calibrated and doesn’t need extra components so you can measure relative humidity and temperature right away.
- 3 to 5V power and I/O
- 2.5mA max current use during conversion (while requesting data)
- Good for 0-100% humidity readings with 2-5% accuracy
- Good for -40 to 80°C temperature readings ±0.5°C accuracy
- No more than 0.5 Hz sampling rate (once every 2 seconds)
Qucik View -
Bosch BMP180 Barometer Pressure/Temperature/Altitude Sensor (Arduino Compatible)
₦ 1,500The BMP180 is a precision barometric pressure, temperature and altitude sensor from manufactured by Bosch. It is fully compatible with BMP085 in terms of firmware/software/interfacing. BMP180 can easily be configured to work with Arduino, ARM or PIC over I2C.
Specification
- 3-5V Logic and Power
- Pressure sensing range: 300-1100 hPa (9000m to -500m above sea level)
- Up to 0.03hPa / 0.25m resolution
- -40 to +85°C operational range, +-2°C temperature accuracy
- This board/chip uses I2C 7-bit address 0x77.
Arduino sample code: //www.haoyuelectronics.com/Attachment/GY-68/bmp085_arduino.zip
Datasheet: //cdn-shop.adafruit.com/datasheets/BST-BMP180-DS000-09.pdf
Product InformationBrandQucik View -
Pulse Sensor -Arduino Compatible
₦ 6,000This pulse sensor measure heart rate by simly being in contact with a finger or earlobe.
- 3-5V Operation
- Pulse Sensor Board
- Coded Cable with Standard Male Headers
For a tutorials and sample code, visit: //pulsesensor.com/pages/code-and-guide
Qucik View -
MQ-135 Air Quality/Pollution Sensor – Arduino Compatible
₦ 3,500The MQ-135 air quality and pollution sensor detects hazardous gases such as benzene, alcohol, smoke, CO2, NH3 and NOx(Nitrous Oxides) in the air. Analog out put can be interfaced directly to ADC of a microcontroller.
- 5V Operation.
- High sensitivity and response time.
Sample Applications: This sensor can be used to build air quality sensing devices for indoor and outdoor applications)
Qucik View -
Type K Thermocouple
₦ 2,500A device for measuring temperature
- Type: K / E (Optional)
- Probe Material: Stainless Steel
- Temperature Range: 0~400 degrees Celsius
Qucik View -
W1219 Thermostat Temperature Controller Switch Module + Waterproof NTC Sensor Module
₦ 6,500A digital temperature controller module with dual LED display and an inbuilt relay module for control. The cut-off temperature is set with buttons on board
- Control Range:-50~110 Celsius
- Control Precision:0.1 Celsius
- Measuring Input: NTC10K waterproof sensor L=0.5m
- High Temperature Alarm:-49~110 Celsius
- Input Voltage: DC 12V
- Output Type: relay output 10A (max)
- Return Difference Setting:0.1~30 degree Celsius
- Delay Starting:0-10min
Qucik View
Reviews
There are no reviews yet.