Only logged in customers who have purchased this product may leave a review.
KY-031 Percussion Knock Sensor – Arduino Compatible

KY-031 Percussion Knock Sensor – Arduino Compatible
₦ 1,000
This module is a knock sensor. It sends out signals which can be read with a microcontroller like Arduino. It is suitable for building projects like electronic drums, and sensing other kinds of vibration. It can be used in anti-theft projects and noise detection systems.
- Working voltage: 5V
- 3 Pinout: 5V, GND, Vout
- Size: 30*20mm
- Weight: 3g
Related Products
-
0 out of 5
MQ-8 Hydrogen Gas Sensor – Arduino Compatible
₦ 3,000The MQ-8 hydrogen gas sensor, allows hydrogen gas concentrations to be measured. It has a sensitivity of 100-10000ppm. The Output is simply connected to an ADC via a load resistor
- 5V Operation
- Easy connection
- Highly sensitive
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
MQ-135 Air Quality/Pollution Sensor – Arduino Compatible
₦ 3,000The MQ-135 air quality and pollution sensor detects hazardous gases such as benzene, alcohol, smoke, CO2, NH3 and NOx(Nitrous Oxides) in the air. Analog out put can be interfaced directly to ADC of a microcontroller.
- 5V Operation.
- High sensitivity and response time.
Sample Applications: This sensor can be used to build air quality sensing devices for indoor and outdoor applications)
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Arduino Mega
₦ 28,500The Arduino Mega is just the Arduino for when you need to bring the big guns out. It has 54 GPIO, 4 UART pins, 16 Analog inputs and more
Features
- Microcontroller ATmega2560
- Operating Voltage 5V
- Input Voltage (recommended) 7-12V
- Input Voltage (limits) 6-20V
- Digital I/O Pins 54 (of which 15 provide PWM output)
- Analog Input Pins 16
- DC Current per I/O Pin 40 mA
- DC Current for 3.3V Pin 50 mA
- Flash Memory 256 KB of which 8 KB used by bootloader
- SRAM 8 KB
- EEPROM 4 KB
- Clock Speed 16 MHz
- Resettable polyfuse that protects PC USB ports from shorts and overcurrent
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
20 X 4 LCD Module – Arduino Compatible
₦ 5,000This 20 X 4 LCD Module allows you to fit in a lot more text than you can on the smaller 16X4. It is however fully compatible. It has the industry standard HD44780 LCD controller.
-
- 20X4 Characters
- 5V Operating voltage
- Fully pin and code compatible with 16X2, 16X1 LCDs
- Backlight
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
-
0 out of 5
Arduino Ethernet Shield
₦ 13,000This Ethernet Shield which is based on the W5100 Ethernet Chip gives you an easy way to get your device Online. It is directly supported by official Ethernet Library. It adds a micro-SD card slot, which can be used to store files for serving over the network
- Operating voltage: 5V
- Input voltage: 7-12 V
- SRAM: 2 KB
- EEPROM: 1 KB
- Clock speed: 16 MHz
- DC current per I/O pin: 40 mA
- DC current for 3.3 V pin: 50 mA
- Power over Ethernet ready Magnetic jack
- MicroSD card slot
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Arduino Nano
₦ 7,500The Arduino Nano is a full featured breadboard-friendly Arduino board. It is based on an Atmega 328 microcontroller. Fully programmable with Arduino IDE
Key Features:
- 5V Operating Voltage
- 7-12 Volt Unregulated Supply Voltage
- 8 Analog Input Pins
- 14 Digital I/O Pins
- 32kB Flash Memory (2kB Bootloader)
- 1kB RAM
- 512 Bytes EEPROM
- UART
- SPI
- PWM
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View
Reviews
There are no reviews yet.