Only logged in customers who have purchased this product may leave a review.
CP2102 MICRO USB to UART TTL Module
CP2102 MICRO USB to UART TTL Module
₦ 1,500
5A constant current LED driver and charger for lithium-ion battery
· 3.3V and 5V voltage output
· Supports baud rates from 300bps ~ 1Mbps
On-chip voltage regulator output voltage 3.3V
Supports data formats for 8 data bits, 1 stop bit and parity bits
Connotation 512 byte receive buffer and 512 byte transmit buffer
Support for hardware or X-ON / X-OFF handshake
Out of stock
Related Products
-
0 out of 5
A4988 Stepper Motor Driver Module
₦ 3,000A4988 is a microstepping stepper motor driver. It drives bipolar stepper motors and has adjustable current limit, over-current and over-temperature protection.
Key Featues:
-
- 8V to 32V Operating voltage
- 3-5V logic supply
- Up to 2A output current per coil
- 5 step resolutions: Full step, 1/2 step, 1/4 step, 1/8 step, 1/16 step
- Adjustable maximum current output
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
-
0 out of 5
HC-12 Wireless Serial Module Up to 1km
₦ 10,000Imagine a wireless UART port with a range of up to 1km. You are looking at it
Features
- Working voltage: 3.2V~5.5V
- Default address range: 1km
- Baud rate: 5000bps
- Default idle current: 16MA (In different working modes operating current is different)
- Module dimensions: 27.8 x 14.4 x 4mm
- Operating frequency range: 433.4-473.0MHz, up to 100 channels of communication
- The maximum transmit power: 100mW (settable)
- Default factory settings: Mode FU3, baud rate is 9600bps, communication channels CH001 (433.4M)
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Arduino Buzzer Module
₦ 1,500This module allows you to produce a rich and loud sound from your microcontroller.
- 3.3 V to 5 V Operating Voltage
- 3V to 5V Control
- Works without the need of a separate transistor
- Mounting Hole
Pin Out
-
- VCC (3.3 V to 5 V)
- GND
- I/O Control
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
20 X 4 LCD Module – Arduino Compatible
₦ 8,250This 20 X 4 LCD Module allows you to fit in a lot more text than you can on the smaller 16X4. It is however fully compatible. It has the industry standard HD44780 LCD controller.
-
- 20X4 Characters
- 5V Operating voltage
- Fully pin and code compatible with 16X2, 16X1 LCDs
- Backlight
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
-
0 out of 5
Arduino Single Channel Relay Module 5V/10A
₦ 1,500This product is a 1-channel relay module board with LED indicators, It can be controlled by microcontrollers such as Arduino, AVR, PIC, ARM any other microcontroller operating at 5V.
With this relay you can easily control electrical appliances, lights, etc.
Features
-
- Diode protected input
- This relay module is 5V active low.
- It is an 1-channel relay interface board, which can be controlled directly by a wide range of microcontrollers.
- It is also able to control various appliances and other equipment with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Can be connected directly to microcontoller GPIO pins.
- Working status indicator lights are conducive to the safe use.
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
-
0 out of 5
12V Relay Module – 10A –Pair
₦ 1,500This 6V Relay allows your to control loads with up to 10A consumption
Features:
-
- 6V Coil
- Maximum Load DC: 24V (DC) @ 10A
- Maximum Load AC: 240V (AC) @ 10A
- Maximum turn-on time: 10ms
- Maximum turn-off time: 5ms
- Easy through hole mounting arrangement
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
Reviews
There are no reviews yet.