Only logged in customers who have purchased this product may leave a review.
Class D High Power Digital Amplifier Board – TDA7492 -2 x 50W
₦ 10,000
A powerful amplifier with 50W output on 2 channels, this board allows a very powerful output to be delivered from a single rail power supply.
- Power supply: Single Supply 10-26V DC voltage
- The Maximum power: 50W per channel (8 Ohm)
- Mono power 100W (4 Ohms)
- Size: 57 mm * 70mm * 21 mm
2 in stock
Related Products
-
Adjustable Power Supply Voltage Regulating/Reduction – LM 2596S
₦ 1,000Excellent for powering GSM modules, charging batteries, etc
Input: 3~ 40V; Output 1.25 ~ 35V ( Adjustable)
Max 3A Output Current
Suggest to work within 2.5A for long term use
Configurable to charge different kinds of sealed lead acid batteries.
Configurable to charge mobile phones at 5V with a very smooth output voltage.
Qucik View -
Resistor Value Pack – 22 Values
₦ 2,000This 22 Value resistor pack contains most of the resistors you will need 10 pieces each of resistors ranging from 10Ω to 10MΩ
- 10Ω
- 22Ω
- 47Ω
- 100Ω
- 220Ω
- 330Ω
- 470Ω
- 680Ω
- 1kΩ
- 2.2kΩ
- 4.7kΩ
- 6.8kΩ
- 10kΩ
- 22kΩ
- 47kΩ
- 68kΩ
- 100kΩ
- 220kΩ
- 470kΩ
- 680kΩ
- 1MΩ
- 10MΩ
Qucik View -
3V to 5V USB Output Charger Step up Power Module
₦ 1,000This module is used as a DC-DC booster, converting 3V to 5V. With the aid of this board, you can charge your mobile phones and power other kinds of USB devices from power sources with voltage as little as 1.5V such as batteries.
- Non-isolated step-up module (BOOST)
- Input voltage: 1-5V
- Output voltage: 5.1-5 .2 V
- Output Current: Rated 1A-1.5A
- Efficiency: Up to 96% (the higher the input voltage, the higher the efficiency)
- Switching frequency: 500KHz
- Output ripple: 30mV (MAX) 20M bandwidth (input 4V output 5.1V 1A)
- Voltage indication: LED lights with load (input voltage less than 2.7V LED indicator off)
- Operating Temperature: Industrial (-40°c to +85°c)
- Full load temperature rise: 30°c
- Quiescent Current: 130uA
- Load regulation: ± 1%
- Voltage regulation: ± 0.5%
- Dynamic response speed: 5% 200uS
- Short circuit protection: None (Please use the lithium battery with protection.)
Qucik View -
SMD to DIP Adapter (QFP, TQFP, FQFP, LQFP)
₦ 1,000This SMD Adapter let’s you solder 0.5mm and 0.8mm SMD Integrated Circuits (IC) such as Atmel, MSP, STC and Microchip microcontrollers
- 0.5mm and 0.8mm on opposite sides
- 32-100 pin SMD components
- 0.8mm side allows mounting of 32 to 64 pin components
- 0.5mm side allows mounting of 32 to 100 pin components
- Applicable to common package: QFP, TQFP, FQFP, LQFP, etc.
- Size: 38 * 46mm
Qucik View -
R2323 to TTL Converter with Dupont Cable
₦ 1,600This module suitable for any 3.3v or 5v microcontroller and Arduino
• Fully compatible with existing legacy COM port software
• Output signals: VDD, TXD, RXD, CTS, RTS, GND
• Power, TX, RX LED
• Power input: 3.3V or 5VPackage List:
1 * RS232 Serial To TTL Converter Module
4 * Dupont Jumping CableQucik View -
5V 30A Single Channel Relay
₦ 2,200This product is a 1-channel relay module board with LED indicators, It can be controlled by microcontrollers such as Arduino, AVR, PIC, ARM any other microcontroller operating at 5V.
With this relay you can easily control electrical appliances, lights, etc.
Features:
- 5V Operation
- The static current:5mA
- Working current:190mA
- Trigger current:2-4mA
Module interface specifications:
-
- DC+ : DC power supply positive pole
- DC- :DC power supply negative pole
- IN : signal triggering pin
- JD+ : relay control voltage positive
- JD- : relay control voltage negative
- It is an 1-channel relay interface board, which can be controlled directly by a wide range of microcontrollers.
- It is also able to control various appliances and other equipment with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Can be connected directly to microcontoller GPIO pins.
- Working status indicator lights are conducive to the safe use.
Qucik View
Reviews
There are no reviews yet.