Only logged in customers who have purchased this product may leave a review.
Channel Digital Amplifier Board with Subwoofer Output




Channel Digital Amplifier Board with Subwoofer Output
₦ 6,500
This stereo amplifier is allows you to easily deliver a powerful sound up to 200W! And all you need to do is connect a transformer.
FEATURES
- Output power:80W+80W
- Output Impedance:4-8 Ohms
- Frequency range:20Hz-30kHz
- Microphone input
- SNR:100dB
- Number of channels:3 (left channel,right channel,subwoofer)
- Product size: about 13.2*14.2*6.1cm/5.2* 5.6*2.4inch
- Power Supply: AC +/-24V (>120w) ring transformer (Please use a high power transformer or DC power supply for best output.
Out of stock
Related Products
-
0 out of 5
Arduino Buzzer Module
₦ 1,500This module allows you to produce a rich and loud sound from your microcontroller.
- 3.3 V to 5 V Operating Voltage
- 3V to 5V Control
- Works without the need of a separate transistor
- Mounting Hole
Pin Out
-
- VCC (3.3 V to 5 V)
- GND
- I/O Control
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
5V Electronic Buzzer
₦ 1,000-
- 40mA Current (Max)
- 80dB at 20cm Sound Output
- 100Hz Frequency
- 26mm Diameter
- 2mm Mounting holes
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
-
0 out of 5
ARM STM32F103C8T6 Development Board
₦ 11,000This board is low cost ARM Microcontroller development board – STM32F103C8T6. The board is suitable for learners and professionals alike who want the 32-bit power of ARM Coretex-M3 32-bit core.
Code for it can be written using MirkroC ARM, Keil MDK, Eclipse GCC, and many more.
Easily load code into the chip via UART (check out our USB-UART converter) //www.konga.com/usb-to-uart-5-pin-cp2102-module-serial-converter-1988801
You DON’T need a programmer, flash using //cdn2.starkled.com/content/uploads/2012/11/Flash_Loader_Demonstrator_v2.5.0_Setup.exe
Features
- On-board Mini USB interface, you can give the board power supply and USB communication.
- On-board test indicator LED
- On-board reset button and power indicator LED
- On-board 100ma 3.3V Regulator
- All GPIO are led out and the names of the pins are marked
- After soldering the headers, you can directly plug the board onto the breadboard
Technical Specifications
- CPU Part Number: STM32F103C8T6
- Core: ARM 32 Cortex-M3 CPU.
- Debug mode: SWD (can be programmed with ST-LINK V2)
- CPU Internal Maximum Clock : 72MHz
- External Clock Source: 8MHz crystal
- 64K flash memory, 20K SRAM
- 2.0-3.6V power, I/O
Programming Instructions
- Set Boot Jumper-0 to 1
- Set Boot Jumper-1 to 0
- Connect USB-TTL Converter’s TX to PA10 on STM Board
- Connect USB-TTL Converter’s RX to PA9 on STM Board
- Give 3.3V power to STM board using USB TTL converter
- Press and release reset button once
- Launch STM Flash Loader, Select Port Name (where your usb ttl converter is connected)
- Select Parity as Even, Baudate as 115200, Echo Disabled and Timeout 10s
- Press Next, and follow on screen instructions to program, erase or read STM microcontroller
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
LM2596 Adjustable Step-Down Power Module With Digital Display
₦ 3,500This board carries the multipurpose LM2596 power supply and allows you deliver a regulated voltage for any electronic device without the need for soldering or a multimeter. Simply set it and hook it up. The module displays the output voltage on a built in seven segment display.
Features
- 4V-40V Input Voltage.
- Continuously adjustable output voltage range of 1.25V-37V .
- Maximum output current up to 3A
- Switch toggles between viewing output or input voltage.
- Clear Seven Segment display for showing operating voltages
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Digital Capacitive Touch Sensor – TTP223B
₦ 2,000This device allows you to add touch functionality to your designs. It can be easily interfaced with an Arduino or other microcontroller GPIO pins.
Features:
- Operating Voltage: 2-5V
- Chip: TTP223B
- Response Time: 60-220ms
- PCB Size: 28x20mm
- Fully Arduino Compatible
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
100W Stereo Amplifier Board With Microphone Input
₦ 4,800- Output power:50W+50W
- Output Impedance:4-8 Ohms
- Frequency range:20Hz-30kHz
- Microphone input
- SNR:100dB
- Number of channels: 2 (left channel,right channel)
- Power Supply: AC +/-24V (>120w) ring transformer (Please use a high power transformer or DC power supply for best output.
Package Size:36cm x 33cm x 16cm (14.17in x 12.99in x 6.30in)
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View
Reviews
There are no reviews yet.