Only logged in customers who have purchased this product may leave a review.
AVR Programmer USB-ASP
₦ 9,500
USBasp is a USB in-circuit programmer for Atmel AVR controllers. No special drivers required.
Key Features:
- Read or write the microcontroller EEPROM, firmware.
- Support for Windows, Mac OS X and Linux (will work on Windows 8.1)
- 5 KB/sec maximum write speed
- Software controlled SCK option to support targets with low clock speed (< 1.5MHz)
Related Products
-
USB to RS-485 Converter
₦ 3,000The USB-RS-485 Converter allows you to interface and debug RS-485 devices from any terminal application or terminal application.
Features:
- No need external power, USB powered
- USB 2.0 plug and play compliant
- USB CH340 chip
- Support System: Windows XP , Vista, Windows 7 , Linux , MacOS , and WinCE5.0 support
- Supports baud rate range : 75bps – 115200bps , up to 6Mbps
- Communication distance :1200m(max)
Qucik View -
PIC12F683 Microcontroller
₦ 1,000The Low Pin-count (8 Pins) allows you to add automated control to the smallest projects
- 2.0V – 5.5V Operating Voltage
- Mid-range x14 architecture
- Built in EEPROM Data Memory
- nanoWatt Energy saving technology
- 10-bit A/D (4 Channels)
- Standard Capture/Compare/PWM (CCP) module.
Qucik View -
ARM STM32F103C8T6 Development Board
₦ 9,500This board is low cost ARM Microcontroller development board – STM32F103C8T6. The board is suitable for learners and professionals alike who want the 32-bit power of ARM Coretex-M3 32-bit core.
Code for it can be written using MirkroC ARM, Keil MDK, Eclipse GCC, and many more.
Easily load code into the chip via UART (check out our USB-UART converter) //www.konga.com/usb-to-uart-5-pin-cp2102-module-serial-converter-1988801
You DON’T need a programmer, flash using //cdn2.starkled.com/content/uploads/2012/11/Flash_Loader_Demonstrator_v2.5.0_Setup.exe
Features
- On-board Mini USB interface, you can give the board power supply and USB communication.
- On-board test indicator LED
- On-board reset button and power indicator LED
- On-board 100ma 3.3V Regulator
- All GPIO are led out and the names of the pins are marked
- After soldering the headers, you can directly plug the board onto the breadboard
Technical Specifications
- CPU Part Number: STM32F103C8T6
- Core: ARM 32 Cortex-M3 CPU.
- Debug mode: SWD (can be programmed with ST-LINK V2)
- CPU Internal Maximum Clock : 72MHz
- External Clock Source: 8MHz crystal
- 64K flash memory, 20K SRAM
- 2.0-3.6V power, I/O
Programming Instructions
- Set Boot Jumper-0 to 1
- Set Boot Jumper-1 to 0
- Connect USB-TTL Converter’s TX to PA10 on STM Board
- Connect USB-TTL Converter’s RX to PA9 on STM Board
- Give 3.3V power to STM board using USB TTL converter
- Press and release reset button once
- Launch STM Flash Loader, Select Port Name (where your usb ttl converter is connected)
- Select Parity as Even, Baudate as 115200, Echo Disabled and Timeout 10s
- Press Next, and follow on screen instructions to program, erase or read STM microcontroller
Qucik View -
USB to RS232 Cable HL-340
₦ 3,000A USB to RS232 cable.
- USB to RS232 (9-pin Male) Cable
- USB specification 1.1 and 2.0 compliant
- 4.Support the RS 232 serial interface
- Supports over 1 Mbps data transfer rate
- Windows Vista/7/8/10
Qucik View -
Arduino LilyPad – Atmega 328 Model
₦ 6,000The LilyPad Arduino 328 Board is an Arduino based board designed for making wearable and e-textile type projects. It is fully Arduino compatible and has holes for easily sewing it into projects. LEDs, Sensors, buttons and so much more can be easily integrated.
Features:
- ATmega328 Microcontroller
- Operating Voltage 2.7-5.5 V
- Input Voltage 2.7-5.5 V
- Digital I/O Pins 14
- PWM Channels 6
- Analog Input Channels 6
- DC Current per I/O Pin 40 mA
- Flash Memory 16 KB (of which 2 KB used by bootloader)
- SRAM 1 KB
- EEPROM 512 bytes
- Clock Speed 8 MHz
Qucik View -
ATMEGA 328P-PU
₦ 1,900This high-performance Atmel 8-bit AVR RISC-based microcontroller combines 32KB ISP flash memory
- Flash Memory 32 kBytes
- 1024B EEPROM
- 2KB SRAM
- Pin Count: 32
- Max. Operating Freq. (MHz): 20 MHz
- CPU: 8-bit AVR
- 23 GPIO pins
- 24 Interrupt Sources
Qucik View
Reviews
There are no reviews yet.