Only logged in customers who have purchased this product may leave a review.
Arduino DHT22 + Uno Combo Kit
₦ 25,000
DHT22 and Arduino Uno combo Kit lets you take weather readings with ease. The DHT22 temperature and humidity sensor allows reading to be taken with great ease.
DHT22 Features
- Low cost
- 3 to 5V power and I/O
- 2.5mA max current use during conversion (while requesting data)
- Good for 0-100% humidity readings with 2-5% accuracy
- Good for -40 to 80°C temperature readings ±0.5°C accuracy
- No more than 0.5 Hz sampling rate (once every 2 seconds)
- Body size 27mm x 59mm x 13.5mm (1.05″ x 2.32″ x 0.53″)
- 4 pins, 0.1″ spacing
Arduino Uno Features
- Microcontroller: ATmega328.
- Operating Voltage: 5V.
- Input Voltage (recommended): 7-12V.
- Input Voltage (limits): 6-20V.
- Digital I/O Pins: 14 (of which 6 provide PWM output)
- Analog Input Pins: 6.
- DC Current per I/O Pin: 40 mA.
Kit Contains
- DHT22 Temperature and Humidity Sensor
- Arduino Uno
Product Information
Brand
Related Products
-
PN532 NFC and RFID Reader & Writer Module
₦ 9,000The PN532 is a widely used and supported NFC chip. This module will allow you to add NFC and RFID functionality to your project, allowing you to interact with phones, read and write NFC tags and RFID tags.
Features
- Typical Operating Distance have been updated to 5cm~7cm reading distance
- Work in NFC Mode or RFID reader/writer Mode
- RFID reader/writer supports:
- Mifare 1k, 4k, Ultralight, and DesFire cards
- ISO/IEC 14443-4 cards such as CD97BX, CD light, Desfire, P5CN072 (SMX)
- Innovision Jewel cards such as IRT5001 card
- FeliCa cards such as RCS_860 and RCS_854
- Plug and play, Arduino compatible
- Built in PCB Antenna, with 4cm~6cm communication distance
- On-board level shifter, Standard 5V TTL for I2C and UART, 3.3V TTL SPI
- Work as RFID reader/writer
- Work as 1443-A card or a virtual card
- Exchange data with other NFC devices such as smartphone
Package contains
- 1 PN532 NFC RFID Module
- 1 dupont cable Male-Male
- 1 Mifare S50 White Card
- 1 Mifare One S50 Key Ring
- 1 12P bent header pin
Arduino Library: //github.com/adafruit/Adafruit-PN532
Qucik View -
Arduino Ethernet Shield
₦ 23,000This Ethernet Shield which is based on the W5100 Ethernet Chip gives you an easy way to get your device Online. It is directly supported by official Ethernet Library. It adds a micro-SD card slot, which can be used to store files for serving over the network
- Operating voltage: 5V
- Input voltage: 7-12 V
- SRAM: 2 KB
- EEPROM: 1 KB
- Clock speed: 16 MHz
- DC current per I/O pin: 40 mA
- DC current for 3.3 V pin: 50 mA
- Power over Ethernet ready Magnetic jack
- MicroSD card slot
Qucik View -
Arduino Buzzer Module
₦ 1,500This module allows you to produce a rich and loud sound from your microcontroller.
- 3.3 V to 5 V Operating Voltage
- 3V to 5V Control
- Works without the need of a separate transistor
- Mounting Hole
Pin Out
-
- VCC (3.3 V to 5 V)
- GND
- I/O Control
Qucik View -
Pulse Sensor -Arduino Compatible
₦ 6,000This pulse sensor measure heart rate by simly being in contact with a finger or earlobe.
- 3-5V Operation
- Pulse Sensor Board
- Coded Cable with Standard Male Headers
For a tutorials and sample code, visit: //pulsesensor.com/pages/code-and-guide
Qucik View -
Arduino Single Channel Relay Module 5V/10A
₦ 1,500This product is a 1-channel relay module board with LED indicators, It can be controlled by microcontrollers such as Arduino, AVR, PIC, ARM any other microcontroller operating at 5V.
With this relay you can easily control electrical appliances, lights, etc.
Features
-
- Diode protected input
- This relay module is 5V active low.
- It is an 1-channel relay interface board, which can be controlled directly by a wide range of microcontrollers.
- It is also able to control various appliances and other equipment with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Can be connected directly to microcontoller GPIO pins.
- Working status indicator lights are conducive to the safe use.
Qucik View -
-
Arduino Uno
₦ 16,500The Arduino Uno R3 is a microcontroller board based on the ATmega328. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
The Uno differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip.
Additional features coming with the R3 version are:
ATmega16U2 instead 8U2 as USB-to-Serial converter.
1.0 pinout: added SDA and SCL pins for TWI communication placed near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board and the second one is a not connected pin, that is reserved for future purposes.
stronger RESET circuit.
“Uno” means “One” in Italian and is named to mark the upcoming release of Arduino 1.0. The Uno and version 1.0 will be the reference versions of Arduino, moving forward. The Uno is the latest in a series of USB Arduino boards, and the reference model for the Arduino platform.Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limit) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) PWM Digital I/O Pins 6 Analog Input Pins 6 DC Current per I/O Pin 20 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB of which 0.5 KB used by bootloader SRAM 2 KB EEPROM 1 KB Clock Speed 16 MHz LED_BUILTIN 13 Length 68.6 mm Width 53.4 mm Weight 25 g Qucik View
Arduino CNC Shield V3.0
Reviews
There are no reviews yet.