Only logged in customers who have purchased this product may leave a review.
8-Channel Digital Capacitive Switch Touch Sensor Module For Arduino – TTP226
8-Channel Digital Capacitive Switch Touch Sensor Module For Arduino – TTP226
₦ 4,050
A capacitive touch module which sends out signals on contact, it can be interfaced to an Arduino or any microcontroller. This module can be used to build all kinds of interesting projects from access control, home automation, automotive projects etc
- Onboard TTP226 capacitive 8 keys touch sensor IC
- Onboard 8 channel level status indicator
- Working voltage: 2.4V-5.5V
Out of stock
Related Products
-
0 out of 5
Micro SD Storage Board – Arduino Compatible
₦ 1,500This Micro SD card Adapter easibly adds Gigabytes of storage to your microcontroller project. Read and write from SD & SDHC cards via a microcontroller or Arduino board.
- Support Micro SD SDHC Card
- Power supply:4.5V – 5.5V, 3.3V voltage regulator circuit board
- Positioning holes: 4 M2 screws for mounting
- Control Interface: GND, VCC, MISO, MOSI, SCK, CS
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Arduino Buzzer Module
₦ 1,500This module allows you to produce a rich and loud sound from your microcontroller.
- 3.3 V to 5 V Operating Voltage
- 3V to 5V Control
- Works without the need of a separate transistor
- Mounting Hole
Pin Out
-
- VCC (3.3 V to 5 V)
- GND
- I/O Control
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Arduino Ethernet Shield
₦ 23,000This Ethernet Shield which is based on the W5100 Ethernet Chip gives you an easy way to get your device Online. It is directly supported by official Ethernet Library. It adds a micro-SD card slot, which can be used to store files for serving over the network
- Operating voltage: 5V
- Input voltage: 7-12 V
- SRAM: 2 KB
- EEPROM: 1 KB
- Clock speed: 16 MHz
- DC current per I/O pin: 40 mA
- DC current for 3.3 V pin: 50 mA
- Power over Ethernet ready Magnetic jack
- MicroSD card slot
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Arduino Nano
₦ 9,750The Arduino Nano is a full featured breadboard-friendly Arduino board. It is based on an Atmega 328 microcontroller. Fully programmable with Arduino IDE
Key Features:
- 5V Operating Voltage
- 7-12 Volt Unregulated Supply Voltage
- 8 Analog Input Pins
- 14 Digital I/O Pins
- 32kB Flash Memory (2kB Bootloader)
- 1kB RAM
- 512 Bytes EEPROM
- UART
- SPI
- PWM
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Arduino Camera
₦ 4,500This OV7670 Camera allows image capabilities to be added to a microcontroller or Arduino with ease. It is capable of up to 640 X 480 pixel resolution and has a widely available library.
- Photosensitive array: 640X480
- IO Voltage: 2.5V to 3.0V (internal LDO for nuclear power 1.8V)
- Power operation: 60mW/15fpsVGAYUV
- Sleep: <20μA
- Temperature Operating: -30 ? to 70 ?
- Output Formats (8): YUV/YCbCr4: 2:2 RGB565/555/444 GRB4: 2:2 Raw RGB Data
- Optical size: 1/6 “
- FOV: 25 °
- Maximum Zhen rate: 30fps VGA
- Sensitivity: 1.3V / (Lux-sec)
- SNR: 46 dB
- Dynamic range: 52 dB
- View Mode: Progressive
- Electronic Exposure: 1 line to 510 line
- Pixel Size: 3.6μm x 3.6μm
- Dark current: 12 mV / s at 60 ?
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
MQ-7 Carbon Monoxide Sensor – Arduino Compatible
₦ 4,000The MQ-7 Carbon Monoxide (CO) gas sensor, allows Carbon monoxide concentrations to be measured. It has a sensitivity of 20ppm-2000ppm. The Output is simply connected to an ADC via a load resistor
- 5V Operation
- Safely measure poisonous CO concentrations
- Highly sensitive CO
- Easy connection
- Highly sensitive
Applications: CO alarm, anti carbon monoxide poisoning system.
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View
Reviews
There are no reviews yet.