Only logged in customers who have purchased this product may leave a review.
4 Phase Stepper Motor – 5V + Driver
₦ 2,500
This 5 line 4 phase stepper motor with the included driver ULN2003 board can be used to drive all kinds of projects from robotics, DIY or control and industrial applications
-
- Stepper motor driver board with ULN2003.
- A, B, C, D four-phase LED indicates the status of the stepper motor work.
- Stepper motor with a standard interface.
1 in stock
Related Products
-
28%
DIY Tank Robot SN3900
₦ 18,000₦ 25,000- Good damping effect, you can press down to 0.7cm.
- With general motors 130, support 3-8V voltage
- With the DC charging port at the bottom of the tail.
- Easy to install.
- Ideal for DIY.
Qucik View -
3V to 5V USB Output Charger Step up Power Module
₦ 1,000This module is used as a DC-DC booster, converting 3V to 5V. With the aid of this board, you can charge your mobile phones and power other kinds of USB devices from power sources with voltage as little as 1.5V such as batteries.
- Non-isolated step-up module (BOOST)
- Input voltage: 1-5V
- Output voltage: 5.1-5 .2 V
- Output Current: Rated 1A-1.5A
- Efficiency: Up to 96% (the higher the input voltage, the higher the efficiency)
- Switching frequency: 500KHz
- Output ripple: 30mV (MAX) 20M bandwidth (input 4V output 5.1V 1A)
- Voltage indication: LED lights with load (input voltage less than 2.7V LED indicator off)
- Operating Temperature: Industrial (-40°c to +85°c)
- Full load temperature rise: 30°c
- Quiescent Current: 130uA
- Load regulation: ± 1%
- Voltage regulation: ± 0.5%
- Dynamic response speed: 5% 200uS
- Short circuit protection: None (Please use the lithium battery with protection.)
Qucik View -
Multi Servo Motor Tester
₦ 5,500This simple device can be used to operate or test servo motors. There are 3 modes to check servos;
- Manual mode: turn the knob
- Neutral mode: make the servo go back to the neutral point
- Automatic: window wiper mode: make the servo swing like a window wiper in the biggest angle. Push button to change between modes. Lights indicate mode.
You can connect 1-3 servos simultaneously. It can also be used to check the operation of any servo motor whether fitted or not.
Qucik View -
5V 700mA 220V to 5V Regulator Module
₦ 1,000This module comes in handy when you need to power you circuit from 220V mains supply.
Features:
-
- Input voltage: AC 85 ~ 265 v 50/60 hz or DC 100~ 370 v
- Input current: 0.014A(AC220V)
- Output voltage: DC 5V (+ / – 0.2 V)
- Output current 700 mA
- Power 3.5 W
- Operating temperature -20~60°
- Relative humidity 40-90%
- Output power:0-4W(DC current)
- Output efficiency: 80%
Qucik View -
-
5A DC-DC CC/CV Lithium Charger LED Driver Power Module
₦ 2,500This very utilitarian board delivers constant voltage or constant current output and comes in handy as a battery charger (Lead acid or Lithium battery), LED Constant current driver, as well as other power supply needs. It is also quite chunky -deliverying up to 5A output.
-
- Output voltage: 0.8V-30V
- Input voltage: 5V-32V
- Separately adjustable voltage and current outputs
- Size: 51 * 26.3 * 14 (L * W * H) (mm)
- Operating Temperature: -40 to +85 Degrees
- Voltage Regulation: +/-2.5%
- Load Regulation: +/- 0.5%
- Output ripple: 50mV
- Switching frequency: 300KHz
- Conversion efficiency: 95% (the highest)
- Output current: adjustable maximum 5A
Qucik View -
-
5V DC 2 Channel Solid State Relay Module
₦ 2,000This is a 5V solid state relay 240V 2A, able to control sizable loads.
Features
-
- High current relay, AC250V 10A, DC30V 10A
- 2 LEDs to indicate when relays are on
- Works with logic level signals from 3.3V or 5V devices
- Opto-isolation circuitry
- PCB size: 50×45 mm
Qucik View -
Reviews
There are no reviews yet.