Only logged in customers who have purchased this product may leave a review.
12V Relay – 10A – 1 Pair
₦ 850
The JCQ-3FF 12V Relay allows your to control loads with up to 10A consumption
Features:
-
- 12V Coil
- Maximum Load DC: 24V (DC) @ 10A
- Maximum Load AC: 240V (AC) @ 10A
- Maximum turn-on time: 10ms
- Maximum turn-off time: 5ms
- Easy through hole mounting arrangement
Out of stock
Related Products
-
Stepper Motor – Nema 17 + A4988 Driver
₦ 14,000This stepper motor is perfect for robotics, 3D printer and other kinds of high precision projects. 1.8° per step smooth motion. The included A4988 motor driver allows you to safely, quickly and accurately working with the motor.
- 200 steps/rev
- 12V Operating Voltage
- 350mA (Max Current)
- 1.8 degrees per step
- Bipolar stepper motor
- 20 N*cm, 2 Kg*cm holding torque per phase
- 35 ohms per winding
- 42mm X 42mm square body -M3 Mounting Screws
Qucik View -
MT3608 Power DC-DC Booster Module
₦ 1,500This DC-DC booster module comes in handy when you need a regulated output greater than what you have available. It can be used to boost 3-3.7V battery supply to 5V output or raise a 5V supply to be compatible with a 12V motor.
Technical specifications:
- AeroSemi MT3608 High Efficiency 1.2MHz 2A Step Up Converter integrated circuit.
- The maximum output current: 2A
- The input voltage: 2V ~ 24V
- Output adjustable using a potentiometer
- The maximum output voltage: 28V
- 93% peak efficiency (~200mA output current at 5Vin, 12Vout)
- Product size: 36 mm * 17 mm * 14 mm
Qucik View -
LCR-T4 Transistor, Diode, Triode Capacitance Meter
₦ 7,000The LCR-T4 is a multi-function meter for testing resistors, capacitors, diodes, transistors, mos-tubes, inductors.
Qucik View -
5V 30A Single Channel Relay
₦ 2,500This product is a 1-channel relay module board with LED indicators, It can be controlled by microcontrollers such as Arduino, AVR, PIC, ARM any other microcontroller operating at 5V.
With this relay you can easily control electrical appliances, lights, etc.
Features:
- 5V Operation
- The static current:5mA
- Working current:190mA
- Trigger current:2-4mA
Module interface specifications:
-
- DC+ : DC power supply positive pole
- DC- :DC power supply negative pole
- IN : signal triggering pin
- JD+ : relay control voltage positive
- JD- : relay control voltage negative
- It is an 1-channel relay interface board, which can be controlled directly by a wide range of microcontrollers.
- It is also able to control various appliances and other equipment with large current.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Can be connected directly to microcontoller GPIO pins.
- Working status indicator lights are conducive to the safe use.
Qucik View -
Mini Submersible Water Pump
₦ 2,500This simple DC submersible pump allows you to pump water at a rate of up to 120L/H and operates at 3-5V
Features
- DC Voltage: 3-6V
- Maximum lift:40-110cm / 15.75″-43.4″
- Flow rate:80-120L/H
- Outside diameter of water outlet: 7.5mm / 0.3″
- Inside diameter of water outlet: 4.7mm / 0.18″
- Diameter:Approx. 24mm / 0.95″
- Length:Approx. 45mm / 1.8″
- Height:Approx. 33mm / 1.30″
- Plastic
- Driving mode: Brushless DC Motor
- Continuous working life of 500 hours
Qucik View -
Dupont Cable
₦ 1,000These cables are excellent for all your prototyping needs. Easily connect Raspberry Pi, Arduino boards, ARM based boards and start hacking away.
30 cables in total
- 10 Male-to-Male
- 10 Male-to-Female
- 10 Female-to-Female
Qucik View
Reviews
There are no reviews yet.