Only logged in customers who have purchased this product may leave a review.
DHT11 TEMPERATURE SENSOR
DHT11 TEMPERATURE SENSOR
₦ 2,500
The DHT11 is a low-cost and reliable digital temperature and humidity sensor. Digital output only. It is compatible with Arduino complete with library as well as other microcontrollers.
- 3 to 5V Operating range
- 2.5mA (max)
- 20-80% humidity readings (up to 5% accuracy)
- 0-50°C temperature readings (up to ±2°C accuracy)
- 1 Hz Maximum sampling rate
- 15.5mm x 12mm x 5.5mm
- 4 pins with 0.1″ spacing
Pins
1. VCC
2. Data
3. NC
4. Ground
Related Products
-
0 out of 5
Infra-Red Flame Sensor
₦ 1,500This module is sensitive to the flame and radiation. It also can detect ordinary light source in the range of of a wavelength 760nm-1100 nm. It can be used as a flame alarm or in fire fighting robots.
Features
Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm.
Detection range: up to 100 cm.
Adjustable detection range.
Detection angle about 60 degrees, it is sensitive to the flame spectrum.
Comparator chip LM393 makes module readings stable.
Operating voltage 3.3V-5V.
Digital and Analog Output.
Power indicator and digital switch output indicator.
Interface Description (4-wire)VCC — 3.3V-5V voltage
GND — GND
DO — Digital output interface (0 or 1)
AO — Analog output interfaceProduct added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
DHT22 Temperature and Humidity Sensor
₦ 10,500DHT-22 is a humidity and temperature sensor with read out over single wire digital interface. The sensor is already calibrated and doesn’t need extra components so you can measure relative humidity and temperature right away.
- 3 to 5V power and I/O
- 2.5mA max current use during conversion (while requesting data)
- Good for 0-100% humidity readings with 2-5% accuracy
- Good for -40 to 80°C temperature readings ±0.5°C accuracy
- No more than 0.5 Hz sampling rate (once every 2 seconds)
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
HB100 Motion Detection Microwave Sensor Module
₦ 3,500This is a X-Band Bi-Static Doppler transceiver module. This module can be used to detect motion in projects relating to home automation, automatic doors, alarm systems and even vehicle speed detection.
Feature
Transmission frequency: 10.525 GHz
Frequency Setting Accuracy: 3MHz
Output power (minimum): 13dBm EIRP
Operating voltage: 5V 0.25V
Operating Current (CW): 60mA max., 37mA typical
harmonic emission: <-10dBm
Pulse mode:
Averagecurrent (5% DC): 2mA
Pulse Width (Min.): 5uSec
load cycles (Min.): 1%Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Thermistor Infrared Thermal Sensor Module
₦ 1,500This temperature detection module senses ambient temperature and produces a corresponding output. This module can be used in automatic temperature regulation projects
Features
- Operating Voltage 3.3V-5V
- NTC thermistor sensor
- Thermistor output drives up to 15mA directly
- Adjustable temperature sensitivity
- Analog output (AO pin)
- Digital output with adjustable threshold and LED indicator (DO pin)
- Mounting hole
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Pulse Sensor -Arduino Compatible
₦ 6,000This pulse sensor measure heart rate by simly being in contact with a finger or earlobe.
- 3-5V Operation
- Pulse Sensor Board
- Coded Cable with Standard Male Headers
For a tutorials and sample code, visit: //pulsesensor.com/pages/code-and-guide
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Bosch BMP180 Barometer Pressure/Temperature/Altitude Sensor (Arduino Compatible)
₦ 1,500The BMP180 is a precision barometric pressure, temperature and altitude sensor from manufactured by Bosch. It is fully compatible with BMP085 in terms of firmware/software/interfacing. BMP180 can easily be configured to work with Arduino, ARM or PIC over I2C.
Specification
- 3-5V Logic and Power
- Pressure sensing range: 300-1100 hPa (9000m to -500m above sea level)
- Up to 0.03hPa / 0.25m resolution
- -40 to +85°C operational range, +-2°C temperature accuracy
- This board/chip uses I2C 7-bit address 0x77.
Arduino sample code: //www.haoyuelectronics.com/Attachment/GY-68/bmp085_arduino.zip
Datasheet: //cdn-shop.adafruit.com/datasheets/BST-BMP180-DS000-09.pdf
Product InformationBrandProduct added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View
Reviews
There are no reviews yet.