Only logged in customers who have purchased this product may leave a review.
Arduino Mega
₦ 35,750
The Arduino Mega is just the Arduino for when you need to bring the big guns out. It has 54 GPIO, 4 UART pins, 16 Analog inputs and more
Features
- Microcontroller ATmega2560
- Operating Voltage 5V
- Input Voltage (recommended) 7-12V
- Input Voltage (limits) 6-20V
- Digital I/O Pins 54 (of which 15 provide PWM output)
- Analog Input Pins 16
- DC Current per I/O Pin 40 mA
- DC Current for 3.3V Pin 50 mA
- Flash Memory 256 KB of which 8 KB used by bootloader
- SRAM 8 KB
- EEPROM 4 KB
- Clock Speed 16 MHz
- Resettable polyfuse that protects PC USB ports from shorts and overcurrent
Related Products
-
Arduino Pro Mini
₦ 9,750The Arduino Pro mini is an Arduino board perfect for small applications that need to pack a bang. It has the same microcontroller as the Arduino Uno.
- ATmega328 Microcontroller
- 5 – 12V Supply Voltage
- 16 MHz
- 14 Digital GPIO Pins
- PWM Pins 6
- UART 1
- SPI 1
- I2C 1
- Analog Input Pins 6
- External Interrupts 2
- DC Current per I/O Pin 40 mA
- Flash Memory 32KB (2 KB used by bootloader)
- SRAM 2 KB
- EEPROM 1 KB
A USB to UART converter is needed to program it.
Qucik View -
Graphic LCD 84×48 – Nokia 5110 – Arduino Compatible
₦ 6,000The Nokia 5110 is a basic graphic LCD screen for lots of applications. A much richer information set can be displayed on this screen.
It uses the PCD8544 controller, same used in the Nokia 3310 LCD. The PCD8544 is a low power CMOS LCD controller/driver, designed to drive a graphic display of 48 rows and 84 columns. All necessary functions for the display are provided in a single chip, including on-chip generation of LCD supply and bias voltages, resulting in a minimum of external components and low power consumption. The PCD8544 interfaces to microcontrollers through a serial bus interface.
There is an Arduino library and MikroC library
Qucik View -
Arduino Ethernet Shield
₦ 23,000This Ethernet Shield which is based on the W5100 Ethernet Chip gives you an easy way to get your device Online. It is directly supported by official Ethernet Library. It adds a micro-SD card slot, which can be used to store files for serving over the network
- Operating voltage: 5V
- Input voltage: 7-12 V
- SRAM: 2 KB
- EEPROM: 1 KB
- Clock speed: 16 MHz
- DC current per I/O pin: 40 mA
- DC current for 3.3 V pin: 50 mA
- Power over Ethernet ready Magnetic jack
- MicroSD card slot
Qucik View -
MQ-7 Carbon Monoxide Sensor – Arduino Compatible
₦ 4,000The MQ-7 Carbon Monoxide (CO) gas sensor, allows Carbon monoxide concentrations to be measured. It has a sensitivity of 20ppm-2000ppm. The Output is simply connected to an ADC via a load resistor
- 5V Operation
- Safely measure poisonous CO concentrations
- Highly sensitive CO
- Easy connection
- Highly sensitive
Applications: CO alarm, anti carbon monoxide poisoning system.
Qucik View -
MQ-135 Air Quality/Pollution Sensor – Arduino Compatible
₦ 3,500The MQ-135 air quality and pollution sensor detects hazardous gases such as benzene, alcohol, smoke, CO2, NH3 and NOx(Nitrous Oxides) in the air. Analog out put can be interfaced directly to ADC of a microcontroller.
- 5V Operation.
- High sensitivity and response time.
Sample Applications: This sensor can be used to build air quality sensing devices for indoor and outdoor applications)
Qucik View -
Ethernet Module – ENC28J60
₦ 10,000This module allows you to add Ethernet connectivity to your projects. Based on the popular Microchip’s ENC28J60, this module will easily interface with any Microcontroller or Arduino board allowing Internet Connectivity via the Ethernet..
- Up to 10Mbps
- 5V Tolerant I/O pins
- Fully IEEE 803.2 Standards compatible
Qucik View
Reviews
There are no reviews yet.